Charging The Battery; Volume Control - AEG MMS 4206 Bedienungsanleitung

If your computer runs on Windows 2000 or a more recent sys-
tem, your MP3 player does not require any particular software or
drivers. However, the device does require the latest service pack
version to be installed. In the event of problems try to install
the current Microsoft service pack for the respective operating
system. For this, go to:
http://www.microsoft.com.
Important: Windows 98SE users must install the driver prior to
hooking up the device with the PC. The PC may have to be
restarted. WIN 98 first Edition is not supported.
• Place the supplied CD driver into the CD-ROM drive of your
PC.
• Click on 'Driver'.
• Follow the instructions on how to install.
Connecting the MP3 player with your PC
1. Connect the MP3 player using the USB connection cable,
with your PC.
2. Insert the smaller USB connection into the USB jack (10)
of the MP3 player and the other end into a vacant USB
connection of your PC.
3. Once the connection has been successfully established the
display will read "READY".
4. The MP3 player is displayed as a removable medium and
can be used as such.
5. To store and export fi les, proceed as stated in the operating
software of your PC.
6. Once the fi les have been transferred, fi rst unlog the MP3
player from your PC. Proceed as stated in the operating
software of your PC to safely remove the hardware.
Note:
• Never remove the MP3 player from the PC during data
transfer. This even applies if the data transfer should come
to a halt. To separate the MP3 player from the PC, follow the
notes of your PC software to safely separate hardware, i.e.
the removable medium.
• The exchange of data between the external storage device
(SD/MMC) and the internal storage device (MP3 Player) is
not possible. If you nonetheless wish to transfer fi les from
e.g. the internal memory to the SD/MMC card fi rst save your
fi les on your PC. Then copy the fi les onto the SD/MMC card.
• We can not be held responsible for the loss of fi les as a
result of improper operation.
• The device is not DRM-compatible.
• If an SD/MMC was installed on the PC before connection,
this also appears as a removable medium on the PC.

Charging the Battery

The device is operated by the integrated lithium polymer battery.
In order to recharge the battery, connect the device to your
computer by means of the USB connection cable, or use the
AC/DC adapter of the accessory.
1. Turn the ON/OFF switch (14) to ON (the control lamp in the
microphone (12) lights up).
2. If the device is being charged up by the PC, the word
„READY" appears in the display (7). If charging takes place
05-MMS 4206 AEG 13
via the mains adapter, the device switches on.
Note:
• If only one bar is visible in the battery status display (6), the
charge status of the battery is low and the battery needs
recharging.
• The battery charging time is approx. 4 hours, depending on
the charge status.
• The battery operating time is approximately 6 hours, depen-
ding on the operating parameters (volume).
• The battery is fully charged when the control lamp in the
microphone (12) goes off.
• The PC must be switched on during charging in order for the
battery to be charged.
How to operate the MP3 player
Switching the MP3 player on
In order to switch on the MP3 player, turn the ON/OFF switch
(14) to ON and then keep the II /
ter a few seconds the letters "AEG" appear briefl y in the display.
Depending on the data size the display shows AEG for a shorter
or longer time. . Afterwards the title appears in the display (7).
Switching the MP3 player off
1. While a track is playing, hold the II /
until the display shows "Goodbye".
2. Then move the ON/OFF switch (14) to OFF.
Note: The MP3 player switches itself off automatically if not ope-
rated for a shorter period of time while in stop or pause mode.
When the MP3 player is switched on again and the II /
button (1) is pressed, the device begins to play back the fi rst
piece of music.
Earphones (Fig.3)
1. Release the strain relief (1) of the earphones by pressing
the centre of the release (2).
2. Guide the string (3) of the strain relief through the eyelet (13)
(Fig.1) of the MP3 player.
3. Connect the strain relief (1) with the earphones again until it
catches with a "click".
4. Then connect the 3.5 mm Stereo jack plug (4) with the
earphones connection (9) (Fig.1).
Playing a music fi le
1. Switch on the MP3 player.
2. Press the II / button (1) to start playback ( appears in
the display).
3. Playing of the fi les stored on the device starts.
4. Briefl y press the II / button (1) to pause playback (II
appears in the display).
5. Briefl y press the II / button (1) again to continue
playback from the same point.
Note: If an SD/MMC card is installed, music from the SD/MMC
card is played back last ( appears in the display).

Volume control

1. To increase the volume, press and hold the „
until the desired volume has been set. The volume level is
key (1) pressed down. Af-
button (1) down
" button (2)
13
17.05.2006, 8:32:06 Uhr