Minimum System Requirements; Charging The Battery - AEG MMS 4209 Bedienungsanleitung

How to Install the Driver

Minimum system requirements:

• Pentium 133 MHz or more
• Microsoft ® Windows ™ 98 SE/ME/2000/XP
• RAM 20 MB
• USB Port (2.0)
If your computer runs on Windows 2000 or a more recent sys-
tem, your MP3 player does not require any particular software or
drivers. However, the device does require the latest service pack
version to be installed. In the event of problems try to install
the current Microsoft service pack for the respective operating
system. For this, go to:
http://www.microsoft.com
NOTE:
Important: Windows 98SE users must install the driver prior
to hooking up the device with the PC. The PC may have to be
restarted. WIN 98 fi rst edition is not supported.
• Place the supplied CD driver into the CD-ROM drive of
your PC.
• Click on 'Driver'.
• Follow the instructions on how to install.
Connecting the MP3 player with your PC
1. Connect the MP3 player using the USB connection cable,
with your PC.
2. Insert the smaller USB connection into the USB jack (10)
of the MP3 player and the other end into a vacant USB
connection of your PC.
3. Once the connection has been successfully established the
display will read „READY".
4. The MP3 player is displayed as a removable medium and
can be used as such.
5. To store and export fi les, proceed as stated in the operating
software of your PC.
6. Once the fi les have been transferred, fi rst unlog the MP3
player from your PC. Proceed as stated in the operating
software of your PC to safely remove the hardware.
NOTE:
• Never remove the MP3 player from the PC during data
transfer. This even applies if the data transfer should
come to a halt. To separate the MP3 player from the PC,
follow the notes of your PC software to safely separate
hardware, i.e. the removable medium.
• Unplug the earplugs from the device before you start the
exchange of data.
• We can not be held responsible for the loss of fi les as a
result of improper operation.
• The device is not DRM-compatible.

Charging the Battery

The device is operated by the integrated lithium ion battery. In
order to recharge the battery, connect the device to your com-
puter by means of the USB connection cable, or use the AC/DC
adapter of the accessory.
05-MMS 4209 AEG Neu 13
1. If the device is being charged up by the PC, the word
„READY" appears in the display (7). The charging process is
indicated by the battery status indicator.
2. If charging takes place via the mains adapter, the device
switches on. The display is switched off after some time,
although the charging process is continued. The control
lamp on the mains adapter lights up in red during charging.
NOTE:
• If only one bar is visible in the battery status display (6),
the charge status of the battery is low and the battery
needs recharging.
• The battery charging time is approx. 5 hours, depending
on the charge status.
• The battery operating time depends on the operating
parameters (e.g. volume).
• The battery is fully charged
a) when the battery charge indicator (6) shows that it is
full.
b) when the control lamp on the mains adapter changes
from red to green.
• The PC must be switched on during charging in order for
the battery to be charged.
How to operate the MP3 player
Switching the MP3 player on
In order to switch the MP3 player on, press the II key (1); the
name "AEG / WELCOME!" appears briefl y in the display. The
length of time for which this display appears depends on the
amount of data. The menu then appears in the display (7).
Switching the MP3 player off
While a piece of music is being played back, keep the II key
(1) held down until " (Stopp)" appears in the display. If the II
key (1) is held down a second time until "GOOD BYE!" appears
in the display, the device switches itself off.
NOTE:
• The MP3 player switches itself off automatically if not ope-
rated for a shorter period of time while in stop or pause
mode (see „Power").
• If the „Display" option is activated in the menu the display
switches off after the set time in order to save electricity
(see „Display").
• During the charging process the device cannot be swit-
ched off due to the automatic charging connection.
Earphones (Fig.4)
1. Release the strain relief (1) of the earphones by pressing
the centre of the release (2).
2. Guide the string (3) of the strain relief through the eyelet (2)
(Fig.1) of the MP3 player.
3. Connect the strain relief (1) with the earphones again until it
catches with a "click".
4. Then connect the 2.5 mm Stereo jack plug (4) with the
earphones connection (9) (Fig.1).
13
18.01.2007, 12:42:58 Uhr