Behringer X32 Schnellstartanleitung Seite 7

12 X32 DIGITAL MIXER
X32 DIGITAL MIXER Getting Started
Getting Started
(EN)
Ch01
Inputs 1-8
Local In 1-8
Local In 9-16
[Local In 17-24]
[Local In 25-32]
AES50 A1-8
AES50 A9-16
AES50 A17-24
AES50 A25-32
AES50 A33-40
AES50 A41-48
AES50 B1-8
AES50 B9-16
AES50 B17-24
AES50 A25-32
Routing I/O
The X32 console features 32 analog rear-panel XLR
inputs with microphone-preamps, as well as 16 rear-
panel XLR Outputs and 6 TRS Aux Sends and Returns.
In addition, there are two AES50 ports, each featuring
48 input and output channels, and a card slot for
32 channels of input and output to and from a
connected computer via USB 2.0.
Input Signals can be attached to the console's internal
audio processing engine in blocks of 8 signals from any
one of the aforementioned input sources
Ch01
Analog Output
Output 01
Output 02
Output 03
Output 04
Output 05
Output 06
Output 07
Output 08
*Output 09
*Output 10
*Output 11
*Output 12
*Output 13
*Output 14
Select
Output Signals can be freely assigned from
any internal signal to any of the following outputs:
• • 16x analog local XLR outputs (with adjustable
digital delay for time-alignment of speakers)
6x auxiliary sends on ¼" TRS outputs + 2x
• •
AES/EBU outputs
16x personal monitoring using the console's
• •
P-16 Bus output connector
01 A: S16 A: 48K 13:45
01: 0:00 - 0:00 B: - C: X-USB
home aes50-a
analog out aux out p16 out card out aes50-b
Channel Processing Block Patch
Connected Devices
Inputs 9-16 Inputs 17-24 Inputs 25-32 Aux In 1-4
AES50 A
Local In 1-8 Local In 1-8 Local In 1-8
Aux 1-4
Local In 9-16 Local In 9-16 Local In 9-16
Local 1-4
[Local In 17-24] [Local In 17-24] [Local In 17-24]
AES50 A1-4
[Local In 25-32] [Local In 25-32] [Local In 25-32]
AES50 B1-4
AES50 A1-8 AES50 A1-8 AES50 A1-8
Card 1-4
AES50 A9-16 AES50 A9-16 AES50 A9-16
AES50 A17-24 AES50 A17-24 AES50 A17-24
AES50 A25-32 AES50 A25-32 AES50 A25-32 AES50 B
AES50 A33-40 AES50 A33-40 AES50 A33-40
AES50 A41-48 AES50 A41-48 AES50 A41-48
AES50 B1-8 AES50 B1-8 AES50 B1-8
AES50 B9-16 AES50 B9-16 AES50 B9-16
AES50 B17-24 AES50 B17-24 AES50 B17-24
AES50 A25-32 AES50 A25-32 AES50 A25-32
Note: All signal blocks patched to the audio
processing will be connected to the corresponding
input channels automatically.
Cabling for all AES50 connections between X32 and
S16 stageboxes:
• • Shielded CAT-5e cable
Ethercon terminated cable ends
• •
• • Maximum cable length 100 meters (330 feet)
01 A: S16 A: 48K 14:09
01: 0:00 - 0:00 B: - C: X-USB
analog out aes50-a
home aux out p16 out card out aes50-b
Edit Output Assignment
Current Setting Category Processed Output Signal Tap
MixBus OFF OFF Pre EQ
Main (LRC) Main L Post EQ
Mix Bus Main R Pre Fader
Matrix Main C/M Post Fader
Direct Out Main Bus 01
Monitor Main Bus 02
Main Bus 03
Delay
Main Bus 04
Main Bus 05
Main Bus 06
Main Bus 07
Main Bus 08
Delay
Main Bus 09
Select Select Select
Assign Set Delay
Any and all of the above signals can also be mirrored
in blocks of 8 signals on either one of
• • 48x channels on AES50 port A
48x channels on AES50 port B
• •
• • 32x channels on USB interface card
13 Quick Start Guide
Ch01
01
: 19
01:
config
home
clip
-6
48V
-12
Reverse
-18
-24
-30
Link Lo Cut
-36
-42 +0.0 2.0
dB
-48
-54
Gain Lo Cut
Gain Lo Cut
+0.00 dB 20
Link Lo Cut
LeOnde.mp3
00.05.00 00.00.00
config
home
Bus Configuration
clip
-6
-12
-18
Link
-24
-30
-36
-42
-48
-54
: 37
Gain
00.00 dB
Link
0.3 ft
The confi guration of Mix Bus Channels 1-16 can
0.10 m
0.3 ms
be pre-set (in the Setup/Global page) or can also
be confi gured on an individual, per-channel basis.
The bus processing includes (in this order):
• • Insert point (swappable between post-EQ and
pre-EQ operation)
6-band fully parametric EQ
• •
Delay
• • Compressor/expander (swappable between
0.3 ms
post-EQ and pre-EQ operation)
• • Bus sends to 6 matrices
Main LR panning
• •
• • Mono/Center level
A: S16 A: 48K
14:11
0:00 - 0:00 : 37
B: - C: X-USB
gate dyn eq sends main
Insert Position
t
In
Delay Pre Ins Post
0.3 ft
Source Insert
0.10 m
OFF OFF
Input 01 0.03 ms InsFX 1L
Hz
Input 02 InsFX 1R
Input 03 InsFX 2L
Input 04 InsFX 2R
Delay
Input 05 InsFX 3L
Input 06 InsFX 3L
Source Delay Ins Pos Insert
Hz Input 0.3 ms PRE InsF
Select Delay Insert Connect
13:44:43 MyProj.prj
29 November 2010 Scene01
gate dyn eq sends main
Bus Insert Position
Channel Sends ∑
Pre Insert Post
All Channel Sends Insert
Pre Configuration
Ins 01
... Ins 02
Inputs Ins 03
Pre EQ Ins 04
...
Pre Fader
Post Fader FX 01
Sub Grou FX 02
Send Pos. Insert Pos. Insert
Inputs Pre
Bus Sends Insert Connect
Main Bus Channels LR/C are always available and
independent from Mix Buses. The processing steps
for this signal path include (in this order):
• • Insert point (swappable between post-EQ and
pre-EQ operation)
6-band fully parametric EQ
• •
• • Compressor/expander (swappable between
post-EQ and pre-EQ operation)
Bus sends to 6 matrices
• •
Matrix Channels 1-6 are fed exclusively by
MAIN LRC and Mix Bus 1-16 signals. The processing
steps include (in this order):
• • Insert point (swappable between post-EQ and
pre-EQ operation)
6-band fully parametric EQ
• •
• • Compressor/expander (swappable between
post-EQ and pre-EQ operation)
Input Channels 1-32 are pre-confi gured to use
the fi rst 32 input signals, but can be patched to
use any other available signal on the audio engine
as well, including mix bus/sub group outputs.
Changes of the Channel Source can be made on the
Preamp Confi g page.
Aux Return Channels 1-8 are pre-confi gured
to use the 6 aux input signals, and the two USB
playback outputs, but can be patched to use any
other available signal of the console as well.
FX Return Channels 1L-4R control the 4 stereo
output signals of side-chain FX 1-4.
Eff ects Processing 1-8
The X32 console contains eight true-stereo internal
eff ects engines.
• • FX 1-4 can be confi gured as side chain or insert
eff ects, while FX 5-8 can only be used in insert
points of channels or buses
• • The returns of side chain FX 1-4 can always be
controlled using the 3rd bank (layer) of the input
channels - Aux/USB/FX Returns. Note that the
return signals of FX 1-4 have separate faders for
left and right
The FX Home screen allows selection of the
• •
FX 1-4 input sources and selecting the eff ects
type/algorithm for each of the 8 FX slots of the
virtual rack
The subsequent tabs FX 1-FX 8 of the FX screen
• •
allow editing all parameters of the chosen
eff ects processor
iPad App for X32
Many functions of the X32 console can be remotely
controlled by a dedicated iPad app. Details about
the app's download, setup and operation are
included in a separate user manual available for
download from the X32 product page.
The app's User Interface is optimized for the
touchscreen nature of the iPad device and provides
many useful remote features of the console.
Using the app, you can perform functions such
as adjusting monitor mixes from the stage while
interacting with musicians, or adjusting the front-
of-house mix from the audience, while hearing the
mix exactly as the audience does.