Herunterladen Inhalt Inhalt Diese Seite drucken

Compliance With Weee Directive; Appropriate Installation Location - Beko WMB 71413 LM Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

1.6 Compliance with WEEE Directive

This product complies with EU WEEE Directive (2012/19/EU). This product
bears a classification symbol for waste electrical and electronic equipment
(WEEE).
This product has been manufactured with high quality parts and materials
which can be reused and are suitable for recycling. Do not dispose of the waste
product with normal domestic and other wastes at the end of its service life. Take it to
the collection center for the recycling of electrical and electronic equipment. Please
consult your local authorities to learn about these collection centers.
Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It
does not contain harmful and prohibited materials specified in the Directive.
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If
they are not, call a qualified technician and plumber to have
any necessary arrangements carried out.
C
Preparation of the location and electrical, tap water and
waste water installations at the place of installation is
under customer's responsibility.
B
:
Installation and electrical connections of
warning
the product must be carried out by the Authorized
Service Agent. Manufacturer shall not be held liable for
damages that may arise from procedures carried out by
unauthorized persons.
A
:
Prior to installation, visually check if the product
warning
has any defects on it. If so, do not have it installed.
Damaged products cause risks for your safety.
C
Make sure that the water inlet and discharge hoses
as well as the power cable are not folded, pinched or
crushed while pushing the product into its place after
installation or cleaning procedures.

2.1 Appropriate installation location

• Place the machine on a rigid floor. Do not place it on a
long pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product
on a solid and flat floor that has sufficient load carrying
capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature
may fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
2.2 Removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
68 / EN
2.3 Removing the transportation locks
A
:
Do not remove the transportation locks before
warning
taking out the packaging reinforcement.
A
:
Remove the transportation safety bolts before
warning
operating the washing machine! Otherwise, the product
will be damaged.
1. Loosen all the bolts with a suitable spanner until they
rotate freely (C) .
2. Remove transportation safety bolts by turning them
gently.
3. Attach the plastic covers supplied in the User Manual bag
into the holes on the rear panel. (P)
C
Keep the transportation safety bolts in a safe place to
reuse when the washing machine needs to be moved
again in the future.
C
Never move the product without the transportation safety
bolts properly fixed in place!
2.4 Connecting water supply
C
The water supply pressure required to run the product is
between 1 to 10 bars (0.1 – 1 MPa). It is necessary to
have 10 – 80 liters of water flowing from the fully open
tap in one minute to have your machine run smoothly.
Attach a pressure reducing valve if water pressure is
higher.
Washing Machine / User's Manual

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis