Behringer XENYX UFX1204 Bedienungsanleitung Seite 8

14 XENYX UFX1204
XENYX UFX1204 Controls
Step 2: Controls
(EN) (1) XLR balanced input.
(2) LINE/HI-Z input.
(3) LINE/HI-Z button (Channels 1 & 2 only).
When HI-Z mode is engaged, you can plug
your guitar or bass into this input without
using an external direct (D.I.) box.
(4) +48 V Phantom power is used for condenser
microphones that require between 9 V DC and
48 V DC power to operate.
(5) LOW CUT button fi lters out frequencies
below 80 Hz.
(6) GAIN knob adjusts the sensitivity of the MIC
and LINE/HI-Z inputs.
(7) SEND lets you choose to route your input
signal to FireWire/USB pre or post EQ.
(8) COMP(RESSOR) knob adjusts the amount of
compression eff ect on the channel.
(9) EQ knobs adjust the HIGH, MID, and LOW
frequencies of the channel. Adjust the FREQ
knob to select the specifi c frequency adjusted
by the MID knob.
(10)
EQ button turns the EQ section on and off .
(11) AUX / FX knobs adjust how much of the
channel's signal is sent to the AUX SEND jacks
and/or the internal FX processor.
(12) PAN knob positions the channel's signal in the
stereo fi eld.
(13) MUTE button removes the channel from the
MAIN MIX and sends it to the ALT 3-4 bus.
(14) SOLO button sends the channel signal to
the solo bus (Solo in Place) or to the PFL bus
(Pre-Fader Listen).
(15) LEVEL METER shows the input signal level of
the channel's input signal.
(16)
CHANNEL FADER adjusts the channel volume.
(17) LINE IN left and right input jacks for mono or
stereo signals.
(18)
LINE/FW 1-2 (3-4) button allows the
signal from a computer to be routed via
FireWire/USB to these channels and controlled
by the EQ and AUX and fader functions.
NOTE: All FireWire (FW) routing switches
work for USB connectivity to a computer and
for the USB stand-alone mode depending
on how you have the MODE selector switch
(48) set.
(19) 4-band EQ for the stereo channels.
(20)
BAL(ANCE) knob controls the relative volume
of the left and right input signals before they
are routed to the stereo main mix bus.
(21)
CONTROL ROOM OUT jacks carry the summed
eff ects and main mix signals, as well as soloed
channel signals.
(22) MAIN OUT jacks for connecting line level signal
to powered speakers or external amplifi er.
(23)
ALT 3-4 OUT jacks for connecting line
level signal of an alternate stereo mix to
a recording device, powered speakers
or external amplifi er. Can also be used
for subgrouping.
(24)
CD/TAPE IN and OUT for connecting a stereo
source or for sending the main signal to an
external recorder.
(25) PHONES jacks for connecting headphones.
(26)
INPUT level meters display the signal input
intensity going into the FX bus.
(27) FX eff ect knob selects which eff ect is applied
to the signal.
(28) EDIT knob adjusts the eff ect's main parameter.
(29)
FX ON button turns the eff ect on and off .
(30) The TAP/SELECT button performs two
functions. Hit the button several times in the
tempo of the music piece to adapt the delay
time of presets 9 and 15 or the modulation
speed of presets 10-12. The Button will
start fl ashing in the corresponding tempo.
The TAP/SELECT button also changes the
characteristic of the second parameter on
presets 1-8, 13-14 and 16. By pressing the
button you can toggle between two diff erent
values (light off /on) for the second parameter.
15 Quick Start Guide
(31) FW/USB LED indicates the computer is (46) USB DRIVE jack for use with external USB
connected (based on the selection switch hard disk drives (recommended) or thumb
on back panel). drives in STAND ALONE mode.
(32) (47)
VU METER displays the MAIN OUTPUT USB jack for connecting to a computer.
signal level.
(48) MODE selector switch.
(33) MODE button determines whether the
(49)
FireWire jack for connecting to a computer.
SOLO button operates in "Solo in Place"
(button out) or "Pre-Fader Listen" (50) CHANNEL INSERTS allow you to connect
(button in). PFL is preferred for gain external eff ects to the individual channels
setting purposes. (1-4) PRE-FADER and PRE-EQ.
(34) PHONES knob controls the volume level of (51) MAIN OUTPUTS for sending MAIN MIX via
the PHONES jacks. balanced XLR cables.
(35) (52)
CONTROL RM knob controls the volume of the AUX(ILIARY) SENDS route the 2 auxiliary bus
CONTROL ROOM OUT jacks. signals via balanced or unbalanced ¼" cables.
(36) SOURCE monitoring select buttons (53) AUX(ILIARY) RETURNS allow you to bring
route the signal to either the a stereo eff ects signal routed from an
CONTROL RM/PHONES jacks (left column) AUX SEND jack, through a processor,
or the MAIN MIX (right column). back into the designated auxiliary bus.
These inputs can also be used to connect
(37) PRE/POST fader select buttons for the
additional line sources such as keyboards.
AUX and FX SEND busses.
(38)
AUX SEND 1-2 knobs adjust the level from
send busses 1-2 (rear panel), internal FX bus
(AUX 2 only), and FW 13-14 channels for
recording (post knob).
(39) Destination routing switch for AUX RETURN 2
(to MAIN bus or AUX SEND 1 bus).
(40) AUX RETURN 1-2 knobs adjust the level of
AUX RETURN busses 1-2 (rear panel) or return
signal from internal FX (AUX 2 only).
(41)
MUTE, SOLO, and output LEVEL knobs for
ALT 3-4 bus.
(42) TALKBACK MIC (Built-in), LEVEL knob
(adjusts TALKBACK microphone volume),
DESTINATION switches, and TALK button
(press while talking).
(43) 16 TRACK USB DRIVE RECORDER/MIDI
TRANSPORT CONTROL for use while
connected to a computer via FireWire or
USB as a MIDI Machine Control. Also used
in STAND ALONE MODE for controlling the
internal USB recorder functions.
(44)
MAIN MIX stereo fader adjusts the overall
output of the mixer.
(45) POWER ON turns the mixer on.