Connecting The Receiver; Connecting The Antenna; Connecting With A Scart-Cable - AEG DVB-T 4544 Bedienungsanleitung

Купить в интернет-магазине http://clatronic-shop.com.ua
ENGLISH
30
No. Symbol Explanation
14 OK – Confirming the menu or a
menu option.
– Displaying the list of stations.
15 V- – lower volume.
– Menu option to the left.
– Move to the left in the
zoomed picture.
V+ – raise volume.
– Menu option to the right.
– Move to the right in the
zoomed picture.
16 MENU Calling up the menu, carrying
out basic settings.
17 EPG Electronic Programme Guide.
18 FAV – Views the favorite list.
– Rewinds in PVR recordings.
19 PAGE UP/ – Starts the PVR playback.
– Moves to the previous page /
moves backward by ten (e.g.
within the channel list).
20 0-9 Directly selecting the channel,
entering digits.
21 STANDBY Switching on and switching to
standby mode.

Connecting the receiver

Caution!
Before connecting, remove all films from the receiver
and the remote control. Otherwise, the receiver may be
damaged or the remote control may fail to function
properly.
Caution!
Only connect the receiver to the mains power supply
once you have properly connected it to all devices and
the antenna.

Connecting the antenna

The receiver is connected to the antenna via an antenna
cable. You can connect the receiver via your house an-
tenna or an active or passive DVB-T antenna.
When connecting a DVB-T antenna, make the
following settings after properly installing the
receiver. (Commissioning: see P. 32 ff.)
ТВ-ресивер AEG DVB-T 4544
Activating or deactivating voltage at the antenna out-
put
 Press the "MENU" button.
 Use the cursor buttons "► V+" and "◄ V-" to call up
 Use the cursor buttons "▼ CH-" and "▲ CH+" to call
 Use the cursor buttons "▼ CH-" and "▲ CH+" to enter
You may choose between the following options:
• On -provides the voltage to feed an active DVB-T
• Off -to connect a passive DVB-T antenna or roof aerial.
 Use the "► V+" and "◄ V-" buttons to select the
 In order to exit the menu, press the "EXIT" button
Connect roof aerial or passive DVB-T antenna
 Connect the antenna cable's connector to the "ANT IN"
Connect active DVB-T antenna
To use the receiver with an active DVB-T antenna you
must first switch on the voltage at the antenna outlet (see
page 30). In this case, the active DVB-T antenna receives
the required power from the antenna port of the receiver.
 Connect the antenna cable's connector to the "ANT IN"

Connecting with a SCART-cable

 Connect the antenna cable's connector to the "ANT IN"
 Insert the SCART cable into the "TV SCART" connection
 Connect the SCART cable to the TV set. Note the oper-
 If you would like to connect a video recorder, insert a
the "SETUP" menu.
up the "Installation" menu. Press the "OK" button.
the "Antenna Setting" settings.
antenna. At the receiver's antenna port, a 5V-voltage
is present.
No voltage is present at the receiver's antenna port.
desired setting.
repeatedly.
Please note: If the maximum current of 100 mA
is exceeded, the message "antenna overload"
appears. Please check your aerial connection.
antenna connection on the receiver.
Caution!
Please pay caution to the instructions given in the Oper-
ating Manual of your active DVB-T antenna. Otherwise
the receiver could become damaged.
antenna connection on the receiver.
antenna connection on the receiver.
on the receiver.
ating instructions supplied for your TV set.
SCART cable into the "VCR SCART" connection on the
receiver.