Inhaltsverzeichnis
Werbung
Referenzen
MIDI-Datenformat
1. MIDI functions on the DME8i-C,
DME8o-C, and DME4io-C
1.1 Scene Change
Scene recall occurs according to the "MIDI Program Change Ta-
ble" assignments when appropriate MIDI Bank Select MSB/LSB
and Program Change messages are received by the DME8i-C/
DME8o-C/DME4io-C.
When a scene recall operation is carried out via DME Designer,
corresponding MIDI Bank Select MSB/LSB and Program Change
messages are also transmitted by the DME8i-C/DME8o-C/
DME4io-C as specified by the "MIDI Program Change Table" as-
signments.
Transmission does not occur while configurations are being
switched.
1.2 Parameter Control
MIDI Control Change and Parameter Change messages trans-
mitted to the DME8i-C/DME8o-C/DME4io-C can be used
to control parameters according to the "MIDI Control Change
Table" and "MIDI Parameter Change Table" assignments.
When a parameter is edited via DME Designer, correspond-
ing MIDI Control Change and Parameter Change messages
are also transmitted by the DME8i-C/DME8o-C/DME4io-
C as specified by the "MIDI Control Change Table" and
"MIDI Parameter Change Table" assignments.
"MIDI Program Change Table," "MIDI Control Change Table," and "MIDI
Parameter Change Table" assignments can be made via DME Designer.
Refer to the DME Designer Owner's Manual for details.
2. MIDI Data Flow
MIDI IN
MIDI Rx CH
Bank Select MSB/LSB
Program Change
Control Change
Parameter Change
SW1:
Program Change Rx Switch [On/Off]
SW2:
Control Change Rx Switch [On/Off]
SW3:
Parameter Change Rx Switch [On/Off]
SW4:
Program Change Echo Back Switch [On/Off]
SW5:
Control Change Echo Back Switch [On/Off]
SW6:
Parameter Change Echo Back Switch [On/Off]
SW7:
Program Change Tx Switch [On/Off]
SW8:
Control Change Tx Switch [On/Off]
SW9:
Parameter Change
MIDI Rx CH: MIDI Rx Channel (1-16)
MIDI Tx CH: MIDI Tx Channel (1-16)
38
DME8i-C/DME8o-C/DME4io-C Bedienungsanleitung
Bank Select MSB/LSB
SW1
Program Change
(Scene Recall)
Control Change
SW2
(Parameter Edit)
Parameter Change
SW3
(Parameter Edit)
Bank Select MSB/LSB
Program Change
(Echo Back)
SW4
Control Change
(Echo Back)
SW5
Parameter Change
(Echo Back)
SW6
MIDI Tx CH
MIDI OUT
SW7
SW8
SW9
MIDI THRU
3. MIDI Setup
Specifies basic MIDI operation. Use DME Designer to make the
setting.
3.1 Host Select
Selects the input/output ports to be used for MIDI communica-
tion.
3.2 MIDI Tx Channel
Specifies the MIDI transmit channel (1 ~ 16).
3.3 MIDI Rx Channel
Specifies the MIDI receive channel (1 ~ 16).
3.4 MIDI Tx Switch
Program Change Tx Switch: turns Bank Select MSB, LSB, and
Program Change transmission on or off.
Control Change Tx Switch: turns Control Change transmission on
or off.
Parameter Change Tx Switch: turns Parameter Change transmis-
sion on or off.
3.5 MIDI Rx Switch
Program Change Rx Switch: turns Bank Select MSB, LSB, and
Program Change reception on or off.
Control Change Rx Switch: turns Control Change reception on or
off.
Parameter Change Rx Switch: turns Parameter Change reception
on or off.
3.6 MIDI Omni Switch
Program Change Omni Switch: turns the Bank Select MSB, LSB,
and Program Change omni mode on or off.
Control Change Omni Switch: turns the Control Change omni
mode on or off.
3.7 MIDI Echo Back Switch
Program Change Echo Back Switch: turns Bank Select MSB, LSB,
and Program Change echo back on or off.
Control Change Echo Back Switch: turns Control Change echo
back on or off.
Parameter Change Echo Back Switch: turns Parameter Change
echo back on or off.
Werbung
Inhaltsverzeichnis
