Track Mark; Pfl (Pre Fader Level); Replacing The Crossfader; Specifications - Denon DN-X400 Bedienungsanleitung

TRACK MARK

6
• CD category digital signals are output from the DN-X400's digital outputs. Track numbers can be added at any
position during recording of these signals onto a digital recorder.
• Connect the DN-X400's digital outputs to the digital recorder. (Refer to v CONNECTIONS on page 7.)
1
Start recording on the digital recorder.
Press the TRACK MARK button.
• The output signal's track number changes
and the green indicator lights for 4 seconds.
2
TRACK
MARK
lit

PFL (Pre Fader Level)

7
1. Press the HEADPHONE mode button.
2. Press the CUE button that you wish to monitor 1~4 (make sure your source is playing).
3. Turn the blue GAIN level knob until the L/CUE (top) meters peak at the 0 dB level.
4. Perform your mix using the cross fader or channel fader at your desire.
NOTES:
• For proper operation, your channel levels should always be set to or left on reference line 8.
• This adjustment can be made even if the channel fader is set to zero level.

REPLACING THE CROSSFADER

8
The Crossfader may be removed without any disassembly of the DN-X400 itself.
1. Remove the two A outer screws attaching the crossfader assembly to the front panel.
2. Pull the Crossfader Assembly forward and unplug the ribbon from the connector on the panel board.
3. Install the replacement assembly by reversing the above instructions.
NOTE:
During the 4 seconds in which the track number
is being changed, the track number cannot be
changed again.
A
A

SPECIFICATIONS

9
GENERAL
Dimensions: 482 (W) x 105 (H) x 177 (D) mm (without feet)
Installation: 19-inch rack mountable 4U
Mass: 5.5 kg
Power supply: 120 V AC ±10%, 60 Hz (U. S. A. and Canada models)
230 V AC ±10%, 50 Hz (European models)
Power consumption: 26 W
Environmental conditions: Operational temperature: 5 to 35°C
Operational humidity:
Storage temperature:
AUDIO SECTION
Input Sensitivity & Impedance:
Main Mic -54 dBV (2.0 mV)
Aux Mic -60 dBV (1.0 mV)
Effect (Return) -10 dBV (316 mV)
2-Phono -50 dBV (3.0 mV)
8-Line -14 dBV (200 mV)
Output level & Impedance:
Main (Balanced) 4 dBm (1.23 V)
Main (Unbalanced) 0 dBV (1.0V)
Booth/Zone (Balanced) 4 dBm (1.23 V)
Rec (RCA) -10 dBV (316 mV)
Effect (Send) -10 dBV (316 mV)
Subwoofer -2 dBV (800 mV)
Headphone -4 dBV (631 mV)
Frequency Response:
Line 20 to 20 kHz
Phono 20 to 20 kHz
Mic 20 to 20 kHz
Signal to Noise ratio:
Line 80 dB
Phono 75 dB
Main Mic 65 dB
Total harmonic distortion rate:
Line Below 0.05%
Phono Below 0.05%
Cross talk: Over 70 dB
Channel equalizer:
Hi +10 dB, -26 dB (13 kHz)

Mid

+10 dB, -26 dB (1 kHz)
Low +10 dB, -26 dB (70 Hz)
Microphone equalizer:
Hi +12 dB, -12 dB (10 kHz)
Mid +12 dB, -12 dB (1 kHz)
Low +12 dB, -12 dB (100 Hz)
Digital output (COAXIAL):
Signal format IEC958 Type
0.5 Vp-p 75 Ω/ohms
Output level
Output signal level -6 dB
Digital output (OPTICAL):
Signal format IEC958 Type
Specifications and design are subject to change without notice for purpose of improvement.
(41 to 95°F)
25 to 85% (no condensation)
-20 to 60°C (4 to 140°F)
10 kΩ/kohms
10 kΩ/kohms
50 kΩ/kohms
50 kΩ/kohms
50 kΩ/kohms
600 Ω/ohms load
1 kΩ/kohms
600 Ω/ohms load
1 kΩ/kohms
1 kΩ/kohms
1 kΩ/kohms
150 Ω/ohms (33 Ω/ohms load)
±2 dB
RIAA ±2 dB
±2 dB
0 dBm, 1 kHz, EQ flat
0 dBm, 1 kHz, EQ flat
0 dBm, 1 kHz, EQ flat
II
II
ENGLISH
9