Koch 14000 Gebrauchsanweisung Seite 4

Adjusting possibilities at the sensor
Field Meaning
Change of Number of transmitter
Reset of the sensor
Essential information about channels
The measured temperatures at the sensors will be transmitted via radio waves (433,92 MHz)
via three channels. When you have installed more than one sensor, you are able to switch
between the sensors by pressing the CHANNEL-button. Hold the Channel button for some
seconds (confirming beep) to change over to the auto-scroll-mode, where there is a change
between the sensors every five seconds. To deactivate the auto-scroll-mode olease press
another time on the CHANNEL-button. When you only work with one sensor, or only one
channel is booked I, the CHANNEL-button has no function.
Attention!
If you work with more than one sensor, please take care, that every sensor is
adjusted at a different channel (by adjusting the moving switch inside the
sensor's battery compartment (
The display of sensor temperatures at the base station
When you have inserted all batteries in all units, you should see in the top display the outer
temerature. If not, you should press with a pointed item (pen, nail, etc.) the button TX/Hold
RESET at the back side of the transmitter. At least then it should book in at the base station.
If not, you should rotale the sensor in 45° steps, press again the a.m. button and wait for a
short time, unit locks in.
If there had been a functional transmission, and the display flashing "-.-", there might be
interruption of transmission or log-in of another unit. Check first if you can switch to the
desired channel via the CHANNEL-button. If this doesn't work, confirm that your batteries are
fully operational. If this is okay as well, make a forced transmission by pressing the TX/Hold
RESET-button at the sensor.
Installing 12/24 Hours
The unit will be delivered in the 24-hour-time-system usual in Europe. The mode can be
changed manually. When your base station is showing the humidity or the outer temperature,
you should change over to the time mode by pressin once or twice on the Indoor-button.
When time is displayed, you should press the second button from the left (HOLD 12/24) at
the back side of the base station for approx. 3 sec., then there will be a change of the two
modes automatically.
Installing °C / °F
Standard is a delivery in the °C-Mode, like usual in central Europe. To change over your
bottom display should humidity or internal temperature (both is possible), otherwise you
should change by pressing the indoor button. Then press at the back side of the unit for a
short time the second button from the left (°C/°F), then there will be a change between the
two display
(Please change to the time display by pressing the indoor-button).
Pressing the HR-button (third button from the left) at the back side of the base station will
count the hours upwards, pressing the MIN-button (forth button from the left) will count the
minutes. If you press the buttons for longer the counting will speed up. Press it until you
reach the correct time. Counting in the other direction is impossible, so if you exceed the
wanted time you have to start again counting through the hours or minutes.
The Hygrometer
By pressing the INDOOR-button you switch over display the time, the inner temperature and
the relative humidity (RH). Please note, that the hygrometer at the base station can measure
only humidity grades between 20% and 99%.
The Minimum/Maximum-Function
The Min/Max-Function is automatically activated. By pressing the RECALL MEMORY-Button
at the front side of the base station, Outer, Inner and hygrometer (upt to the display) first
shows the highest, afterwards the lowest and than again actual measurements (for the
chosen Sensor at the display). To start a new phase please press the Clear Memory-button.
Then the following dates were deleted:
Parts of Display
Top Outer temp. Sensor 1
Bottom Inner temp.
Top Outer temp Sensor 2
Bottom Hygrometer
Top Outer temp. Sensor 3
Bottom Time
The sensor
Tip:
Before opening the cover remove the
bracket stand like shown in the
drawing. Afterwards you'll see 4
screws, which you have to open.
) to a different position).
Adjusting time
Delete the following limit dates
Min-/Max-Data Sensor 1
Min-/Max-Data Inner temp..
Min-/Max-Data Sensor 2
Min-/Max-Data Hygrometer
Min-/Max-Data Sensor 3
If this fails it is likely that since you first installed the sensor the unit has encountered electronic
or magnetic disturbances that interfere with the function of the unit. This can be confirmed by
bringing the sensor to a short distance to the base station to re-check proper function. To
remove a sensor manually from the base station, please choose at the normal display mode (not
Auto-scroll), by pressing the REMOTE CHANNEL-button the sensor you want to delete. Please
press afterwards HOLD/CLEAR at the back side for more than 3 sec. and the chosen sensor will
be removed (-.- is been shown at the display)
Um einen Sender manuell von der Basisstation zu trennen, wählen Sie im normalen
Anzeigemodus (nicht AUTO SCROLL), durch Drücken auf die REMOTE CHANNEL-Taste, den
zu löschenden Sender. Drücken Sie danach HOLD/CLEAR auf der Rückseite für mindestens 5
Sekunden und der gewählte Sender wird von der Basisstation getrennt (-.- erscheint blinkend im
Anzeigefeld).
1. Do not clean the units with abrasive or corrosive compound. It may scratch the plastic parts
and corrode the electronic circuits.
2. Do not subject the units to excessive force shock, dust, temperature or humidity, which may
result in malfunction, shorter electronic life span, damaged battery and distorted parts.
3. Do not tamper with these units' internal components. Doing so will invalidate the warranty of
unit and may cause unnecessary damaged battery and distorted parts.
4. Do not expose the units to excessive direct sunlight. The remote sensor is splash proof.
Never immerse it in water or expose it in heavy rain.
Installing the base station / Insertion of batteries
Open the gap fort he batteries at the back side of the unit (by moving the door indirection of the
trinagle) ( )) and insert the batteries from the top to bottom. Remind the polarity markings. The
base station will start beeping and making a self test showing all display contents
Installing the sensor
Take off the bracket stand at the back side and open the battery vompartment at the back side
by opening the four small srews. Insert from top to bottom two AAA Batteries. Remind the
polarity markings.
!!!Special note regarding the changing of batteries in the transmitter!!!
If you have already connected to an external transmitter, you will have to
disconnect the communications between the transmitter and the base station
by pressing the button HOLD/CLEAR at the back side of the base station.
So if you only want to delete the Data of the outer sensor, please pay attention that at the
bottom display you have chosen the display of the actual time.
Free chosen Alarm
1. Press and hold the ALERT ON/OFF-button at the backside of the base station for approx 3.
sec.. There will be a beep and some lines at the display will flash.
2. Choose with the button REMOTE CHANNEL at the front of the base station the sensor (IN for
inner or 1,2 or 3 for the outer sensors flashing).
3. After an additional short pressing of the button the upper alarm temperature is flashing (at the
first time +50°C, afterwards the last adjusted upper temperature). This you can adjust with the
buttons + and – (the known buttons HR and MIN, the third and fourth button from thie left side at
the backside of the base station)
4. Afterward an additional short pressing of the button the bottom alram temperature can be
fixed (at the first time +30°C, afterwards the last adjusted upper temperature). Adjusting takes
place like above mentioned.
5. After three sec. Waiting (without pressing any button) the data is been chosen. If you have not
reached the aimed temperature yet, you have to begin the process from the start
When you have adjusted the temperature limits like above mentioned, you can activate the
alarm by pressing the ALERT ON/OFF-button at the backside of the base station. The symbol
is been shown at the display. Another pressing of the button will deactivate it again, and the
symbol vanishes again.
IYour product was thoroughly inspected and tested before shipping. Should you have a
complaint, you may file a claim as perm the terms our manufacturer's warranty within two years
of purchaseof the product. KOCH reserves the right to repair or to exchange the defective
product. If the product is no longer available at the time claim is made, we reserve the right to
exchange the product for a product with the same or higher value. KOCH and its suppliers hold
no responsibility to you or any other person for any monetary damages, lost profits or other
claim.
Product specification:
Displayed indoor temperature range:
Recommended remote sensor
operating range:
Batteries
Transmission range
Himidity measurement display range:
Resolution hygrometer:
The device could be sensitive for electrostatic discharge, if it or malfunction occurs, please reset
the unit.
Attention:
• The above content is subject to change without notice.
• The displays is printed in this manual may be different from the actual display
because of printing limitation.
Precautions
1) Adjustment
2) Activating
Quality notes
0°C bis +50°C (+32°F bis +122°F)
-10°C bis +50°C (+14°F bis +122°F)
MIGNON AA 1,5V 2 St. (Base Station)
MICRO AAA 1,5V 2 St. (Sensor)
30 m, open area
20% - 99 % rel. Humidity
1 % rel. Humidity