Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Configuration mode
4.11
Note on 2-loop device: After loop 1 has been set, the parameters for loop 2 are set (make the settings using the same procedure) and the settings are not shown in the table with the exception of the direction logic
Button operation
parameter
LCD
Button operation
Function
display
functions
0 - Basic function
Mode
1
Sim1
1 - Time function
Mode
1
Sim1
2 - Time unit
Mode
1
This display does
Sim1
not appear with
time function th ( )
3 - Time factor
Mode
This display does
1
Sim1
not appear wih time
function th ( )
4 - Sensitivity
Mode
1
5
Sim1
= Sensitivity
5 - Automatic
ASB stands for
Mode
1
Sim1
Automatic Sensiti-
Sensitivity Boost
vity Boost
ASB
6 - Frequency
Mode
1
Sim1
This display appears
7 - Direction logic
Mode
1
2
Sim1
only with a
2-loop device
8 - Output 2
Mode
1
Sim1
configuration
9 - Protection
Mode
Sim1
against power
failure
A - Operating
1
mode
Table 4.11b Different product variants (setting options)
ProLoop2
Output 2
1-loop device, 2 relays
–
1*/0
active
–
2-loop device, 2 relays
deactivated 1/0*
Data
Sim2
Door/gate
1
Barrier systems
systems*
On delay
*
1
1
0.1 second
1 second*
Set value between 1
1
and 99 by touching or
1*
holding the «Data»
button
Set value betw. 1 (lowest
1
) and 9 (highest sensi.)
4*
by touching or holding
the «Data» button
1
Switched off*
Switched on
1
Frequency F4*
Frequency F1
1
2
Both directi-
Loop 2 to loop
ons*
1
2
Output 2 is
Output 2 is
switched off
activated
Switched off*
Switched on
Operating
1
Error memory
mode
slot 1
Notes
1 = Output 2 on; 0 = Output 2 off
Parameter 8 is not possible and is not displayed
1 = Output 2 on; 0 = Output 2 off
Data
Data
Sim2
Sim2
1
1
Quiescent current
Direction logic
Off delay
Activation
pulse loop
1
1
1
1
1 minute
1 hour
1
1
1
Frequency F2
Frequency F3
1
2
1
2
Loop 1 to loop 2
2
Error memory
Error memory slot 2
slot 3
Data
Data
Sim2
Sim2
Only 2-loop device:
1
2
Loop 2
2
activated: «1»*
deactivated: «0»
Time funct. pulse
Max. presence
when loop is exited
1
1
1
1
Error memory
Error memory
slot 3
slot 5
Data
Sim2
Notes
With deactivation of Loop 2
the output 2 becomes
configurable
8
1
The time unit multiplied by
the time factor gives the
set time.
Setting restrictions:
rotection against power
failure (with P1): Value 1-5
The direction logic function
can only be implemented
with 2 loops and a 2-loop
device
Loop 2 has to be
deactivated «0»
9
P 1
If parameter
=
5
A0
parameter 5 must be set to off
(
=
).
Possible displays in case of
error: see chapter 6 of these
operating instructions
Werbung
Inhaltsverzeichnis
Fehlerbehebung
