Initial Startup - Kärcher AFG 100 Handbuch

The mounting hole for the screw is recessed.
3. Use the Allen key to screw the stand onto the stand
pipe of the air purifier and firmly tighten the screw.
4. Position the mounted device upright on the stand.
5. Remove the 3-stage filter cartridge from the device
and remove the protective foil.
6. Remove all transport locks above and below the 3-
stage filter cartridge.
7. Insert the 3-stage filter cartridge according to the in-
structions.
 See: Inserting the 3-stage filter cartridge
Inserting the 3-stage filter cartridge
1. Pull the control unit upwards and out.
2. Fold the control unit to the side.
3. Remove the transport lock from the 3-stage filter
cartridge.
4. Insert the 3-stage filter cartridge.
Note
The three spacers must be fitted in the recesses on
the device.
The 3-stage filter cartridge can only be inserted in
one position.
5. Insert the control unit into the top of the device.
Note
The control unit only latches fully in one position.
The device cannot be switched on if the control unit
is not fully latched in position.
Erecting the device
1. Place the device on a flat, stable surface.
Note
Do not place the device on hot surfaces or in the im-
mediate vicinity of the room heating.
Do not allow any liquids or foreign bodies (e.g. me-
tallic objects) to enter the device.
2. Ensure that the air intake (at the bottom) and air ex-
haust (at the top) are not blocked or impeded.
3. Connect the device to the mains socket using the
mains cable provided.
4. Your Kärcher AFG 100 is now ready for operation.
Note
The first time you use the device, we recommend al-
lowing it to run overnight to perform an initial basic
cleaning of your room.

Initial startup

Switching the device on/off
1. Plug the mains plug into the mains socket.
2. Push the On/Off button to switch on the device.
Note
The device starts up with the last settings.
When fan level "0" is set, the device can be switched
off by briefly pressing the On/Off button.
Switching the fan on/off
Switching the Press the Fan button twice in succes-
fan on sion if the fan is switched off.
The fan runs at the last level selected.
Switching the Press the fan button twice in succes-
fan off sion.
Note
In automatic mode, a sensor measures the air quality as
soon as the device is switched on. This procedure takes
at least 2 minutes.
After measuring the air quality, the fan automation sys-
tem automatically controls the device.
16
1. Press the fan button to adjust the fan.
 The fan button lights up.
Note
The fan automation system first takes affect 2 minutes
after switch on at the earliest.
The fan automation system first takes affect 15 minutes
after switch on at the latest.
Display Meaning
0 Fan level 0
1...5 Fan level 1...5
AU Automatic mode
Fan lev- Operating mode Application example
el
1 - 2 Quiet continuous
night time opera-
tion
3 Continuous day-
time operation
4 Continuous day-
time operation
5 High speed mode For fast air purification or
AU Automatic mode
Setting the fan levels
Setting the fan
level
Selecting auto-
matic mode
Setting the colour
1. Press the colour button to set the lighting colour.
 The colour button lights up.
Display Meaning
0...10 Colour 0...10 is set.
A1...A9 Colour change through all colours within
X minutes.
Example: A3 = colour change through all
colours within 3 minutes.
English
Setting the fan
Display
Fan levels
Bedroom
Smaller rooms approx.
25 m²
Larger rooms approx. 60
m²
extremely contaminated
air.
The automatic mode ad-
justs the fan level accord-
ing to the degree of con-
tamination measured by
the sensor.
Press the "+" button to increase the
fan level. Hold the "+" button pressed
to automatically increase the fan level.
Press the "-" button to decrease the
fan level. Hold the "-" button pressed
to automatically decrease the fan lev-
el.
Press the "+" button until "AU" is
shown in the display to indicate auto-
matic mode.
Display