Installation; Electrical Connection - AIRFORCE F117 60 PBO Montage- Und Gebrauchsanweisung

GB INSTRUCTION ON MOUNTING AND USE
Check also the drawings on the initial pages with the alphabetical
and numerical references in the explanatory text.
Closely follow the instructions in this manual. We cannot
accept liability for any faults, detriment or fire damage to the
appliance due to non-compliance with the manual's
instructions. Installation and electrical connections must be
executed by a qualified technician. You should affix the hood
to a wall of sufficient weight-bearing capacity, so not to one
made of plasterboard. Do not install it inside a cupboard.
Attach it to the wall using the anchors provided:( Fig. 3 diameter
12, Fig. 5 diameter 8.)

Installation

The cooker hood must be placed at a minimum distance of 65
cm from the cooking plane for electric cookers and 75cm for
gas or mixed cookers.
If the instructions for installation for the gas hob specify a greater
distance, this has to be taken into account.
Do not tile, grout or silicone this appliance to the wall. Surface
mounting only. Do not fix chimney flue to furniture or fly over
shelves unless the chimney flue can be easily removed, in
case maintenance is ever required.
Use
The cooker hood is provided with an upper air exit B for
discharging fumes externally for models including chimney
flue C ( Suction Version A- exhaust pipe not supplied).
If cooking fumes and vapours cannot be externally discharged,
the cooker hood can be used in the recirculating version
F: the installation of 1 active charcoal filter F allows the
recirculation of fumes and vapours through the upper grid G.

Electrical connection

Make sure that there is a power socket near the hood and
that the system has a 30 mA differential. The mains voltage
must be the same as that on the label inside the hood. The
hood has a 1250 mm power cable with or without plug: if it
does have a plug, connect the hood to an accessible
approved socket; or if it does not (connection direct to the
mains), fit an approved bipolar switch with a minimum
contact opening of no less than 3 mm (accessible). This
installation and electrical connection must be executed by a
qualified technician.
Operation
A B
A – lights ON/OFF
B –motor speed OFF
1 – 2 – 3 adjustment hood speed: minimum (1), average (2), maximum (3)
In the case of an excessive concentration of steam, adjust the hood to
maximum speed. We advise starting the hood five minutes before beginning
to cook and continue the function for at least 15 minutes after having finished
g.
cookin
PBQ
1
2
Operation
A
With the hood switched off, pressing any key will activate the control panel
in stand-by mode. The symbols are backlit by a white light, allowing you
view and select the desired function.
Pressing one of the keys again will start the corresponding function, and its
symbol will light up. After all functions have been switched off, the control
panel will remain in stand-by mode for around 30 seconds and then switch
off automatically.
A: Light ON/OFF key: press this touch sensor to switch on or off the lights
of the hood.
C: Motor ON/OFF key (4 speed): press this touch sensor to switch on the
hood extractor fan at the same speed as it was when last switched off. Use
the „D" and „B" keys to vary the speed (power) of extraction.
B: Decrease extraction speed (power) key: press this touch sensor to
reduce the extraction speed of the hood.
D: Increase extraction speed (power) key: press this touch sensor to
increase the extraction speed of the hood.
E: Timer key: when this touch sensor is pressed, independently of the
extraction speed selected, the timer function will be activated. Press once
to set the timer for 5 minutes, press a second time for 10 minutes and a third
time for 20 minutes. During this phase, the „E" symbol will flash.
To reset the timer, press the motor key, „C"
F: Reset filters key: press this touch sensor to reset the signal that warns
that the metal grease filter (1) is saturated and the charcoal filter (2) should
be replaced.
(1)
(2)
Sensor function: pressing the „B" and „D" keys at the same time will
activate the sensor. In this mode the extraction speed sets itself
automatically and the „B e D" key flashes intermittently. To return to manual
operation, press either the „B" or the „D" key.
Operation
3
Light key: Lights ON/OFF.
Key 1: activates the motor at level-one suction power; press key
1 to turn it off.
Key 2: activates the motor at level-two suction power; press key
2 to turn it off.
Key 3: activates the motor at level-three suction power; press key
3 to turn it off.
Key 4: activates the motor at level-four suction power; press key
4 to turn it off.
To turn off the motor, the suction power keys must be in their
original position.
TSL2
C B D
After 40 hours of using the hood, the „F" symbol will flash to
indicate the necessity of cleaning the metal grease filters.
After 120 hours of using the hood, the „F" symbol will light
up to indicate the necessity of replacing the activated charcoal
filters.
1
2
E F
S4
4
3