Preparing For Operation; Starting Operation; Working Advice - Bosch PFS 105 E WALLPaint Originalbetriebsanleitung

OBJ_BUCH-1543-001.book Page 16 Friday, November 18, 2011 9:16 AM
16 | English
Connecting the base unit:
– Firmly insert the second SDS connector of the air hose in
alignment with the arrow mark into the port of the base unit
26.
– Turn the SDS connector until the lock engages.
Note: After use, reattach the protective hose caps to the hose
ends.
Operation
Before any work on the machine itself, pull the mains
plug.

Preparing for Operation

When purchasing paint, observe its environmental compati-
bility.
Preparing the Spray Surface
The spray surface must be clean, dry and grease-free.
When spraying, all non-covered surfaces can be soiled by the
spray mist. Therefore, thoroughly prepare the area around
the surface to be sprayed:
– Cover or mask off floors, furnishings, doors, windows as
well as door and window frames, etc.
Preparing the Paint
– Prepare the paint according to the manufacturer's instruc-
tions.
In case the paint manufacturer does not provide informa-
tion on diluting the paint, we recommend a 10 % dilution
with water.
Recommendation
Initial quantity of paint [ml]
Water [ml]
– Stir the paint thoroughly.
– Fill a sufficient amount of paint into the container 10 using
the filling funnel 28.
– Thoroughly stir the diluted paint in the container once
more.
– Firmly screw the container 10 to the spray gun.
– Carry out a test-spray run on a test surface. (see "Spray-
ing", page 16)
When the spraying pattern is perfect, start the spray job.
or
When the spraying result is not satisfactory or when no paint
comes out, please continue as described under "Correction of
Malfunctions" on page 18.
Adjusting the Suction Tube (see figure B)
– Unscrew the container 10 from the spray gun.
– Turn the suction tube 12 so that the spray material can be
sprayed with almost no residue:
For painting walls toward the front in nozzle
direction
For painting ceilings toward the rear in handle
direction
1 619 929 K18 | (18.11.11)

Starting Operation

Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
During operation, the base unit must always stand hor-
izontally on a level surface. Never tilt the base unit or
set it upright when switched on.
Pay attention that the base unit cannot draw in dust or
other contamination during operation.
Make sure never to spray on the base unit.
Switching On
– Always place the base unit horizontally on a level and clean
surface.
– Plug the mains plug into a socket outlet.
– Grasp the spray gun by the handle and point it at the spray
surface.
– For switching on, turn the control knob 24 on the base unit
toward the right to the stop.
It is recommended to start with the maximum air flow. (see
"Adjusting the Air Flow", page 17)
– Pull the trigger switch 9 on the spray gun.
Note: When the base unit is switched on, air always flows out
at the nozzle .
Switching Off
– Release the trigger switch 9 and turn the control knob 24
toward the left to the stop.
– Place down the spray gun in the set-down port 25.
– Pull the mains plug from the socket outlet.

Working Advice

500 800 1000
50 80 100
Spraying (see figures C–D)
– Firstly, carry out a test-spray run and adjust the spray pat-
tern and the spray material quantity according to the spray
material. (For adjustments, see the following sections)
– Make sure to hold the spray gun with a uniform clearance
of 25 cm vertical to the object being sprayed.
– Move the spray gun evenly cross-wise or up-and-down, de-
pending on the spray pattern setting.
An even surface quality is achieved when the paths overlap
by 4 – 5 cm.
– Avoid interruptions within the spray surface.
Guiding the spray gun evenly will provide uniform surface
quality.
Non-uniform clearance and spray angle lead to heavy forma-
tion of paint mist and thus to an uneven surface.
Never spray the container completely empty. When the suc-
tion tube no longer immerses in the spray material, the spray
jet will break off, resulting in a non-uniform surface.
When spray material deposits on the nozzle needle 16 and the
air cap 3, clean both components with water.
Bosch Power Tools