Riwall PRO 39048029914 Originalanleitung Seite 37

Use only special files for chainsaws! Other files have the
wrong shape and the wrong cut.
Select the file according to the diameter of your chain
pitch. Make sure to observe the following angle when
sharpening the chain diameter.
A = filing angle
B = the angle of the side plate
The angle must also be maintained for all knives.
For irregular angles, the chain is run irregularly, wear
quickly and break down prematurely.
Since these requirements can only be met with sufficient
and regular exercise:
• A File Holder must be used when sharpening the saw
chain by hand. The correct filing angle marked on it.
• Hold the file horizontally (at a right angle to the guide
rail) and file according to the angle mark on the file
holder. Support the file holder on the top plate and
depth gauge.
• File down. The knife is always from the inside to the
outside
• The file sharpens only in forward motion. Lift it off in
the backward motion.
• Do not touch the dynamic links with the file.
• Turn the file regularly continue to avoid a onesided
wear.
• Remove to remove a piece of hard wood, bones raw
edges.
All knives must have the same length, otherwise they will
also vary. As a result, the chain is irregular and it increas-
es the risk of going broke.
Oiling the gears (pole saw)
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig.47(Q).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not
overfill.
Check the hedge trimmer for obvious faults such as:
– loose attachments
– worn or damaged components
– bent, broken or damaged cutting tools
– correctly attached and working covers and safety de-
vices
– wear, in particular, cutting tool play
Immediately replace damaged or blunt cutting tools,
even in the event of minor damage.
Oiling the gears (hedge trimmer)
Oil the gears every 10 to 20 operating hours.
1 Position the grease gun at the lubricating nipples
Fig.41(P).
2 Insert some grease.
Attention! Fill only a small amount of grease. Do not overfill.
Oil the cutting tools and the angle adjustment with envi-
ronmentally friendly lubricant.
Adjusting the idle speed Fig. 50
If the cutting device runs idle, correct the idle speed.
1. Allow the engine to warm for 3-5 minutes
(No high speeds!).
2. Turn the adjusting screw (S): clockwise
- idle speed increases (+)
counterclockwise
- Idling speed decreases (-)
The idle speed is 3000 min-1
Contact the manufacturer if the cutter continues to run at
idle.
Do not continue to operate the unit!
Lubricate angle transmission
Lubricate with lithium-based grease. Remove the screw
and put in the grease, turning the shaft manually until
grease emerges, then replace the screw.
Storing the unit
After cutting, clean the unit thoroughly. Store the unit in a
dry room allow the motor to cool down beforehand.
Important hint in case of sending the equipment to a
service station:
Due to security reasons please see to it that the equip-
ment is sent back free of oil and gas!
Ordering replacement parts
Please quote the following data when ordering replace-
ment
parts:
• Type of machine
• Article number of the machine
Replacement parts / accesories:
For the cutting equipment listed here, you can always use
the safety guards provided with the unit.
Grass trimmer/brush cutter:
Spool with Ø 430
Blade with 3 teeth Ø 255 x 1.4
Transport guard for blade 3 teeth
Blade with 4 teeth Ø 255 x 1.5
Transport guard for blade 4 teeth
Blade with 8 teeth Ø 255 x 1.5
Transport guard for blade 8 teeth
Safety shield for grass trimmer
Pole pruner:
Saw chain Oregon 91PJ040X
Guide rail Oregon 100SDEA318
Transport guard for chain
Extension for pole pruner
Hedge trimmer:
Blade for hedge trimmer 400 mm
Transport guard for blade
7910700701
7910700702
3904801065
7910700705
3904801066
7910700711
3904801066
3904801023
7910700704
3904801037
3904801039
7910700710
7910700703
3904801043
GB 37