Werbung
Operating Hints
This chapter contains excerpts from the operating instructions. For further particulars please refer to the appropriate user instructions the part number of which is indicated in the
relevant spare parts list.
General
The receiver is already preprogrammed to the cur-
rent stations of many satellites (see Station table).
New stations arrive again and again and station
frequencies are changed.
The following sections describe how to make the
required corrections.
You can find the current station frequencies on the
teletext pages of certain stations (e.g. SAT 1: tele-
text page 675, or 3SAT: teletext page 620) or in a
current satellite magazine. Stations can be repro-
grammed via the menu.
Display on the receiver
Every time a menu is displayed on the picture
screen (e.g. main menu or timer menu), "05d"
(= ON SCREEN DISPLAY of information) appears in
the receiver's display.
As only a few keys ar required for navigating in the
menus, a brief description of the menu philosophy
will suffice for using the menus.
Important Key Functions for the
Menus
.
Displays the main menu or a sub-menu.
MENUE
Pressing the key for more than 5 s in
stand-by mode calls up the special menu
(system).
] | Moves the white cursor bar up or down.
x c
Change values in the selected line.
0
9
...
Direct entry of digits.
O
Saves the changed or newly set values.
¢
Exits the current menu. Changed values
T XT
EXIT
which have not been saved are restored.
h
Switches on and off the green picture
screen background.
On-screen key explanations
All keys performing a function are shown in the two
bottom menu lines. The possible key functions
depend on the menu line selected.
The Menu Items
Press the
key on the remote control unit.
1
.
MENUE
– The main menu is displayed.
Programm
:
1
A
TV
Name
:
ARD_ _
Frequenz
:
11494.0 MHz
Pol./Ant.
:
Hor.
a
/
0 kHz
Decoder
:
Automatik
LNB LO
:
1
(9,750 GHz)
Kontrast
:
3
(37)
Audio
:
1
( 7,02 St )
0 . . 9
PERI
TXT = Abbruch
OK = Speichern
Selecting programme positions
Programm
:
007
TV
x c
1
Use the
keys or the numeric keys to select
the desired programme position.
g
Use the blue
key to switch between the
2
RADIO
"TV" and "Radio" option in the top right corner.
If you select and save the "Radio" option, the
screen is switched blue when exiting the menu.
Select this option if you wish to programme a radio
station which is not yet preprogrammed.
Decoder settings
Decoder
:
Automatik
1
Use the
x c
keys to select the desired setting in
1
the main menu.
The following decoder settings are possible:
Automatik – Select this option for decoders which
supply a switching voltage (e.g. Pre-
mière); the decoder then is automati-
cally switched into the signal path.
Ein (On) – Select this option for decoders without
switching voltage generation.
2
Press the
.
key to display a submenu for
MENUE
further decoder settings.
DECODER
Norm
:
BB Pal
Signal
:
Video
2
3
TXT = Abbruch
OK = Speichern
Selecting LNB oscillator frequencies
4
LNB LO:
1 (9750)
Use the
x c
keys to select between 4 preset LO
1
frequencies (the assigned LO frequency is shown
5
between brackets).
It is possible to change the preset LO frequencies in
2
a submenu (see following section).
1
2
Preselecting LNB oscillator frequencies
LO 1
:
9,750 GHz pos
To change the preselected LO frequencies, press
the
.
key when in the "LNB LO" line of the
MENUE
main menu.
LNB LO 1
:
9,750
GHz
pos
LNB LO 2
:
9,750
GHz
pos
LNB LO 3
:
10,600
GHz
pos
LNB LO 4
:
11,475
GHz
pos
LNB Spg
:
14/18 Volt
0 . . 9
rot = pos/neg
TXT = Abbruch
OK = Speichern
Enter the frequency directly with the numeric keys
x c
or change it step by step with the
keys.
Use the ] | keys to go to the other LO frequency
settings.
For satellites broadcasting in the 2.5 and 4 GHz
range, LNB's are used which produce a "negative"
picture. In this case, select the "neg" menu option
to get a "normal" picture on the screen.
A negative ("neg") video polarity is automatically
asssigned to LO
frequencies below 7000 MHz
and a positive ("pos") video polarity to higher
frequencies.
You can change the polarity by pressing the red
k
key.
LNB power supply on/off
LNB Spg.
:
14/18 V
In order to change the LNB power supply setting,
press the
.
key when in the "LNB LO" line of
MENUE
the main menu.
x c
Use the
keys when in the "LNB Spg." menu
line to select between "14/18 Volt" (on) and "Aus"
(off).
Werbung
