Before Starting The Machine; Setting The Cutting Height; Fuel And Oil; Operation - Einhell Royal MSB 34 Bedienungsanleitung

Anleitung MSB 34_SPK1:Anleitung BHS 26_D
Remove the securing nut for the blade using the
supplied spark plug wrench (Fig. E2). Important:
Left-hand thread!
Remove the pressure plate cover (Fig. E3/Item 5)
and the pressure plate (Fig. E3/Item 4)
The blade (Fig. E3/Item 3) can now be removed.
To assemble, proceed in reverse order. Please
note that the side of the pressure plate (Fig.
E3/Item 4) with the recess must point towards the
blade.
5.3 Installing the cutting line guard hood
Important: The cutting line guard hood must be fitted
if you wish to work with the cutting line.
The guard hood for the cutting line must be installed
as shown in Figures F1 – F3.
A blade (Fig. F6/ Item A) on the underside of the
guard hood automatically cuts the cutting line to the
optimum length. This is covered by a guard (Fig.
F6/Item B).
Remove the guard before you start working and
replace it when you have finished working.
5.4 Fitting / Replacing the line spool
Line up the hole in the carrier plate with the notch
beneath it and lock the carrier plate with the size 6
Allen key (Fig. F4)
Secure the line spool on to the locating pin (Fig. F5).
Important: Left-hand thread!
To dismantle, proceed in reverse order.

6. Before starting the machine

Check that all moving parts move smoothly before
you start using the machine. Check that all screw
connections are securely fastened and also check all
the safety devices.

6.1 Setting the cutting height

Fit the carrying strap as shown in Figures G1 –
G3.
Hook the machine to the carrying belt (Fig. G4).
Adjust the perfect working and cutting position
using the various strap adjusters on the carrying
strap (Fig. G5).
In order to establish the optimum length of the
carrying strap, you should then make a few
swinging movements without starting the engine
(Fig. H).
The carrying strap is fitted with a quick-release
mechanism. Pull the red strap section (Fig. G6) if you
need to remove the strap quickly.
07.12.2006 9:00 Uhr
Important: Always use the strap when working with
the machine. Attach the strap as soon as you have
started the engine and it is running in idle mode.
Switch off the engine before you take off the carrying
strap.
Check the machine for the following each time
before use:
That there are no leaks in the fuel system
That the cutting unit and all safety devices are in
perfect condition
That all screws are securely fastened

6.2 Fuel and oil

Recommended fuels
Use only a mixture of normal unleaded petrol and
special 2-stroke engine oil. Mix the fuel mixture as
indicated on the fuel mixing table.
Please note: Do not use a fuel mixture which has
been kept for longer than 90 days.
Please note: Do not use 2-stroke oil with a
recommended mixing ration of 100:1. If inadequate
lubrication causes engine damage, the
manufacturer's engine warranty will be voided.
Please note: Only use containers designed and
approved for the purpose to transport and store fuel.
Pour the correct quantities of petrol and 2-stroke oil
into the mixing bottle (see scale printed on the bottle).
Then shake the bottle well.
6.3 Fuel mixture table
Mixing procedure: 40 parts petrol to 1 part oil
Petrol 2-stroke oil
1 liters 25 ml
2 liters 125 ml

7. Operation

Please note that the statutory regulations governing
noise abatement may differ from town to town.
7.1 Starting the engine when cold
Fill the tank with the required amount of oil/petrol mix.
See "Fuel and oil".
1. Set the machine down on a hard, level surface.
2. Set the choke lever (Fig. A/Item 10) to " ".
3. Press the fuel pump (primer) (Fig. A/Item 16) 10
times.
4. Switch the ON/OFF switch (Fig. A/Item 6) to "I".
5. Secure the throttle lever. To do so, actuate the
Seite 19
GB
19