Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DRIVE-08DSP
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
3) For power supply, use the mains cable pro-
vided to connect the mains jack (10) to a
mains socket (230 V~/50 Hz).
5 Operation
1) Before switching on, set the control GAIN (2)
to MIN to make sure that the initial volume
is not too high. Then switch on the speaker
system with the POWER switch (9). The LED
ON /CLIP (1) will light up in green.
2) The button GND/ LIFT (4) is used to suppress
hum noise caused by what is called a ground
loop or by noise interference. In case of hum
noise, engage and disengage the button to
determine when the hum noise stops and
then keep the button in this position. (When
the button is engaged, the signal ground is
connected to the protective conductor of
the power supply.)
Ground loops may occur when two
units are connected both via their signal
ground and via the protective conductor of
the power supply or via a conductive con-
nection of their housings.
3) Use the control GAIN to adjust the desired
volume.
Specifications
Amplifier power
Bass amplifier (Class D)
Tweeter amplifier (Class A / B)
Frequency range
SPL at rated power
Speaker configuration
Bass speaker
Tweeter
Radiation angle of tweeter
Input
Connection
Sensitivity / Impedance
Line
Mic
Output LINK
Ambient temperature
Power supply
Max. power consumption
Dimensions (W × H × D)
Weight
DRIVE-10DSP
ELECTRONICS FOR SPECIALISTS
CAUTION Never adjust a very high vol-
to high volumes which do not seem to be
that high after some time. Therefore, do not
further increase a high volume after getting
used to it.
4) Use the rotary switch PRESET (7) to select the
sound. The setting will not affect the output
signal of the jack LINK (6).
Pos.
Preset
1
Live
2
Music
3
DJ
4
Club
5
Vocal
6
Monitor
7
Wall-mount for wall mounting
8
Subwoofer activation of high-pass
DRIVE-08DSP
300 W
rms
80 W
rms
60 Hz – 20 kHz
116 dB
20 cm (8")
25 mm (1")
horizontal 90° / vertical 60°
XLR / 6.3 mm jack, bal.
260 mV/ 12 kΩ
1.6 mV/ 2.5 kΩ
XLR, input signal
fed through
0 – 40 °C
230 V~/50 Hz
195 VA
290 × 480 × 313 mm
9 kg
Copyright
by MONACOR INTERNATIONAL. All rights reserved.
©
DRIVE-12DSP
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
ume. Permanent high volumes
may damage your hearing!
Your ear will get accustomed
Sound
linear reproduction
slight boosting of bass
and treble
more presence and bass
powerful bass, less treble
ideal setting for reproduc-
tion of vocals and voice
operation as
a floor monitor
filter for operation with
additional subwoofer
DRIVE-10DSP
300 W
rms
80 W
rms
55 Hz – 20 kHz
119 dB
25 cm (10")
25 mm (1")
horizontal 90° / vertical 60°
horizontal 90° / vertical 60°
XLR / 6.3 mm jack, bal..
300 mV/ 12 kΩ
2.4 mV/ 2.5 kΩ
XLR, input signal
fed through
0 – 40 °C
230 V~/50 Hz
250 VA
320 × 504 × 345 mm
12 kg
DRIVE-15DSP
ELECTRONICS FOR SPECIALISTS
5) The LED ON/CLIP will light up in red at the
maximum undistorted signal level. If the LED
lights up frequently, use the control GAIN to
reduce the volume.
Subject to technical modification.
All rights reserved by MONACOR
GmbH & Co. KG. No part of this instruction manual
may be reproduced in any form or by any means for any
commercial use.
DRIVE-12DSP
300 W
rms
80 W
rms
45 Hz – 20 kHz
121 dB
30 cm (12")
25 mm (1")
horizontal 90° / vertical 60°
XLR / 6.3 mm jack, bal.
XLR / 6.3 mm jack, bal..
375 mV/ 12 kΩ
3.0 mV/ 2.5 kΩ
XLR, input signal
fed through
0 – 40 °C
230 V~/50 Hz
300 VA
350 × 612 × 383 mm
416 × 678 × 454 mm
17.5 kg
A-1736.99.02.02.2016
ELECTRONICS
®
INTERNATIONAL
DRIVE-15DSP
300 W
rms
80 W
rms
40 Hz – 20 kHz
122 dB
38 cm (15")
25 mm (1")
370 mV/ 12 kΩ
2.8 mV/ 2.5 kΩ
XLR, input signal
fed through
0 – 40 °C
230 V~/50 Hz
330 VA
21.5 kg
Werbung
