Werbung
Verfügbare Sprachen
Verfügbare Sprachen
DRIVE-08DSP
DRIVE-10DSP
DRIVE-12DSP
DRIVE-15DSP
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
1
2
3 4 5
GAIN
MIN
MAX
MIC
LINE
INPUT
GND
LIFT
ON/CLIP
PRESET
1
LIVE
2
MUSIC
3
DJ
4
CLUB
5
VOCAL
6
MONITOR
7
WALL-MOUNT
8
SUBWOOFER
100-240V~/
POWER
USE ONLY WITH A 250V FUSE
8
9
10
Professional DSP Speaker System
with 380 W Power Amplifier
These instructions are intended for users
without any specific technical knowledge.
Please read the instructions carefully prior
to operation and keep them for later ref-
erence.
1 Applications
This 2-way speaker system is designed as a full-
range bass-reflex system with separate power
amplifiers for the high-frequency range and the
low-frequency range and is suited for versatile
sound applications. The high-quality cabinet
made of birch plywood allows multiple setup
options (use as a floor monitor, wall or stand
mounting, suspended installation).
The DSP (digital signal processor) offers
eight selectable presets for an optimum sound.
It is, among other features, also equipped with
an integrated limiter to protect the speakers
and to prevent signal distortion.
Order No. 25.7450
Order No. 25.7460
Order No. 25.7470
Order No. 25.7480
ELECTRONICS FOR SPECIALISTS
2 Overview
6
7
1 LED ON / CLIP
green = normal mode
red
1
8
2
PRESET
7
3
6
4
5
2 Volume control GAIN
LINK
3 Level selector switch MIC / LINE for the sig-
nal input (5):
MIC for a microphone
LINE for an audio unit with line level output
(mixer, CD/ MP3 player etc.)
4 Ground lift switch to suppress noise inter-
ference
engaged: connection of signal ground and
protective conductor
disengaged: separation of signal ground
and protective conductor
5 Signal input INPUT (XLR / 6.3 mm jack, bal.)
to connect a microphone or an audio unit
6 Feed-through output LINK
The signal of the input jack (5) is available
at this output, e. g. to route the signal to
50-60Hz
another active speaker system.
7 Sound selector switch PRESET
8 Heat sink for heat dissipation; do not cover!
FUSE
9 POWER switch
10 Mains jack for connection to a mains socket
(230 V~/50 Hzz) via the mains cable pro-
vided
The fuse holder is underneath this jack;
always replace a blown mains fuse by one
of the same type!
3 Safety Notes
The unit corresponds to all relevant directives of
the EU and is therefore marked with
WARNING The unit uses dangerous mains
•
The unit is suitable for indoor use only. Pro-
tect it against dripping water, splash water
and high air humidity. The admissible am-
bient temperature range is 0 – 40 °C.
•
Do not place any vessel filled with liquid on
the unit, e. g. a drinking glass.
•
Immediately disconnect the mains plug from
the socket
1. if the unit or the mains cable is visibly
damaged,
2. if a defect might have occurred after the
unit was dropped or suffered a similar
accident,
3. if malfunctions occur.
In any case the unit must be repaired by
skilled personnel.
MONACOR INTERNATIONAL GmbH & Co. KG • Zum Falsch 36 • 28307 Bremen • Germany
ELECTRONICS FOR SPECIALISTS
= At the maximum undistorted level,
the limiter will limit the volume to
protect the speaker.
voltage. Leave servicing to skilled
personnel only. Inexpert handling
may result in electric shock.
ELECTRONICS FOR SPECIALISTS
ELECTRONICS FOR SPECIALISTS
•
Never pull the mains cable to disconnect the
mains plug from the socket, always seize the
plug.
•
For cleaning only use a dry, soft cloth; never
use water or chemicals.
•
No guarantee claims for the unit and no
liability for any resulting personal damage
or material damage will be accepted if the
unit is used for other purposes than originally
intended, if it is not correctly connected or
operated, or if it is not repaired in an expert
way.
If the unit is to be put out of operation
definitively, take it to a local recycling
plant for a disposal which is not harm-
ful to the environment.
4 Setting into Operation
4.1 Setting up the speaker system
Place the speaker system on a solid surface
and align it towards the audience. Place the
tweeter at ear level, if possible. The bevelled
design of the cabinet also makes it possible
to operate the speaker system horizontally as
a floor monitor which will radiate the sound
diagonally upwards.
Alternatively, place the speaker system via
the stand sleeve on its lower side on a standard
speaker stand with a tube diameter of 35 mm
(e. g. from the PAST series of IMG STAGE LINE).
For additional mounting options, e. g. suspen-
sion, multiple M8 threaded inserts are provided.
When setting up the speaker system,
always make sure that air will be able to flow
freely around the heat sink (8); otherwise, the
amplifier may overheat and the protective
circuit will mute the sound.
.
4.2 Connection
Before making or changing any connections,
always switch off the speaker system and the
units to be connected!
1) Feed the audio input signal via an XLR plug
or 6.3 mm plug to the jack INPUT (5). This
jack allows to connect the line level output,
e. g. of a mixer, CD- / MP3 player or pream-
plifier. When connecting a line level output,
make sure that the button LINE / MIC (3) is
disengaged.
Alternatively, connect a microphone to
this jack. In this case, engage the button
LINE / MIC.
2) If another active speaker system is required
for sound applications in larger zones, con-
nect the line level input of this speaker sys-
tem to the XLR output LINK (6). The input
signal of the jack INPUT is available at this
output.
ELECTRONICS
Werbung
