Classic smart 4 Universal Bedienungsanleitung Seite 4

GB
USER INSTRUCTIONS
Classic smart 4 Universal Remote Control
INSERTING THE BATTERIES.
Your new smart 4 remote control uses 2 LR03 or AAA Alkaline batteries which
must be installed before it can be used. Always use new batteries of the same
type and install the two new batteries the correct way round as shown by the
battery markings in the battery compartment on the back of the remote control.
Please dispose of used batteries as advised by the battery manufacturer.
SETTING UP YOUR smart 4
Your smart 4 can control 4 devices. TV, VCR, SAT and DVD which can be set up
by entering either a 3 digit code from the code list included in your instruction
book or by using the library search facility. Instructions for both methods follow.
SET UP BY ENTERING A 3 DIGIT DEVICE CODE.
Refer to the device code list in your instruction book and look up the 3 digit code
which corresponds to the brand of the device you wish to control. If there is more
than one code listed against the brand start with the first code. Make a note of the
code and follow steps 1 to 6 below.
1) Switch on the device you wish to control (e.g. your TV)
2) Press and hold down the required device key on the smart 4 (e.g. TV) and
at the same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the device
key being held down lights and remains on. Release both keys.
3) Use the number keys on the handset to enter the 3 digit code you found in
the code list.
4) The indicator will blink.
5) Press and release the device mode key (TV in this example) and the
indicator will blink 3 times. This indicates that you have now stored the code
into the handset.
6) Try all of the functions of the remote control.
7) If your device does not respond or responds incorrectly to the commands
repeat steps 1 to 6 using the next number you found against your brand in
the code list.
If the device key does not blink 3 times at step 5 an incorrect code has been
entered. Check for the correct 3 digit code for your device in the code table
and repeat steps 1 to 6.
Repeat the above procedure to enter the codes for your VCR, Sat and DVD
using the appropriate device key on the Smart 4 and code from the device
code list.
Make a note of the device codes used on the label inside the battery
compartment should these be needed again in the future.
4
SET UP BY USING THE LIBRARY SEARCH FACILITY.
If you cannot identify the correct code for your device from the device code list
use the code search facility.
1) Switch on the device you wish to control (e.g. your TV)
2) Press and hold down the required device key on the smart 4 (e.g. TV) and
at the same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the device
key being held down lights and remains on. Release both keys.
3) Point the smart 4 towards the device you wish to control (e.g. your TV) and
press either the P up or P down key repeatedly until your device switches
off. The P up key searches forwards through the library and the P down key
searches backwards through the library. Alternatively hold down the P up or
P down key and the smart 4 will search through each available code at
approximately one-second intervals.
4) When your device switches off stop pressing the key. Should you
accidentally press the key after your device has switched off you can back
up by pressing the opposite key.
5) Press and release the device mode key (TV in this example) and the
indicator will blink 3 times. This indicates that you have now stored the code
into the handset.
6) Switch your device back on and try all of the functions of the remote control.
7) If your device does not respond correctly to the commands from the remote
control continue the search process until you find a suitable code by
repeating steps 1 to 5. The handset will continue its search from the last
code you selected.
Please be patient when searching by this method as the library contains a
large number of codes and it may take some time to find a suitable code.
READ OUT THE STORED CODE NUMBER.
Having found a suitable code by the search method it is useful to identify the code
number and record this in the battery compartment for future use.
1) Press and hold down the required device key on the smart 4 (e.g. TV) and
at the same time press and hold down the OK key. Keep both keys pressed
down for approximately two seconds until the indicator light on the device
key being held down lights and remains on. Release both keys.
2) Press and release the Mute key.
3) The indicator light will then blink the number of the first digit, pause, blink the
number of the second digit, pause and then blink the number of the third
digit. (e.g. 1 blink = digit 1, 6 blinks = digit 6. Note 10 blinks = digit 0).
4) The handset will then automatically return to normal operation.
GB
5