Menu Overview - AEG FTE 400 Bedienungsanleitung

FTE 400
THERMOSTAT SETUP MENU

Menu overview

Parameter Shown on display
Max. temperature
SCA a Hi
Min. temperature
SCA a Lo a
Max. limit temperature
Li a Hi
FLOOR *1
Min. limit temperature
Li a Lo a 15
FLOOR *1
Min. limit temperature
Li a Lo a -19,5
Limit function *2
Frost protection dEF a 8.0
Night setback nSb a -5.0
Measured floor tem-
FLo a 24.5 (example) *3
perature
Measured room
ro a 21.5 (example) *3
temperature
APp a F
Application
a A
a AF (Room sensor with
a C
a Li
Scale LCd a C
Temperature reading in
dF a SP
start display
Adjust Offset Adj a 24.5 (example)
Control method PWM a On
PWM cycle time *4 cyc a 20
Differential tempera-
dIF a 0.3
ture *5
Relay function
rEL a no
EN50559 PLi a 0
Software version
SU a 1.0
*1 : Only available if APp a AF is selected under Application.
*2 : Only available if APp a Li is selected under Application.
*3 : With no or disconnected sensor, - - is shown on the display.
*4 : Only available if PWM is ON under Control Method.
*5 : Only available if PWM is OFF under Control Method.
If Regulator (C) is selected under Application, the floor and room sensors are discon-
nected and heating is controlled on a scale of 0-10, corresponding to 0-100% of full
power.
Settings
To set parameter values, press and hold the centremost button for
three seconds. SCA a Hi a 40 will appear on the display. Firstly,
SCA will be displayed for 1 second, followed by Hi, and finally 40.
The required value can now be set using the navigation buttons. To
access the next parameter, press the programming button again.
If no button is pressed for 30 seconds, the program returns to the
initial display.
Max. temperature
The highest temperature to which the thermostat can be set.
Min. temperature
The lowest temperature to which the thermostat can be set.
Max. limit temperature
Allows the highest permissible floor temperature to be set for
6
Factory settings
40°C
a 40
(-19.5/+40°C)
0°C
0
(-19.5/+40°C)
28°C
a 28
(-19.5/+40°C + OFF)
15°C
(0/+40°C + OFF)
-19,5°C
(-19.5/0°C + OFF)
8°C
(0/+10°C)
-5 K
(-19.5/+30°C)
(Floor sensor)
F : Floor
(Room sensor)
floor temperature
limits)
Regulator
(Limit floor sensor)
C = Celsius
(nU = numerical)
SP = Setpoint
(tP = actual temp.)
Actual temperature
(+/- 10°C)
On
(OFF)
20 minutes
(10-60 min)
0.3°C
(0.3/10°C)
no = normally open
(nc = normally
closed)
0 min (0-15 min.)
© 2017 OJ Electronics A/S - EHT Haustechnik GMBH
wooden and other floor types when control type has been set to
room sensor with floor limit (AF).
Min. limit temperature - Floor
Allows the lowest permissible floor temperature to be set for tiled
and other floor types when control type has been set to room sen-
sor with floor limit (AF).
Min. limit temperature - Limit function
Allows the lowest permissible temperature to be set in Limit func-
tion.
Frost protection
The lowest temperature for frost protection when the function is
activated via an external signal (fig. 4 in instructions).
Example: The setpoint is 25°C.
Frost protection = 8°C means temp. setting = 8°C.
Night setback / energy-saving function
The number of degrees the temperature setting is to be reduced.
The night setback setting must be preceded by a minus sign (-). Is
controlled via an external signal (fig. 3 in instructions).
Example: The setpoint is 25°C.
Energy-saving function = -5°C means temp. setting = 20°C.
Measured floor temperature
Displays actual floor temperature (if a floor sensor is fitted).
Measured room temperature
Displays actual room temperature.
Application
Sets thermostat function. Select the required control type.
APpa F APpa A
Thermostat with
Floor
sensor for:
Floor x
Room
Room and Floor x
Without
Note: * Room sensor not in use.
Floor (F): The thermostat controls floor temperature
alone.
A floor sensor must be fitted.
Room (A): The thermostat controls room temperature
alone.
Room/limit (AF): The thermostat controls room temperature
while respecting min. and max. limits for floor
temperature. A floor sensor must be fitted.
(Li aLo = 0/40°C)
Regulator (C): The thermostat functions as a simple regulator
and no sensors are used. The setting is in per
cent.
Limit function (Li): Controls only on floor sensor temperature with
min. and max. limits. (Li aLo = -19,5/0°C)

 




Scale
Choose between degrees Celsius and a numerical scale. If the
numerical scale is selected, temperature is set on a scale from 0.0
to 10.0 where 0.0 corresponds to min. temperature (SCA aLo) and
10.0 corresponds to max. temperature (SCA a Hi).
English
APpa AF
APpa Li
Room/
Room Limit Regulator
floor limit
x
x
x x* x
APpa C
x
x
x
x