Unpacking The Device; Initial Operation - Clatronic DR 3280 Bedienungsanleitung

18 Floor brush nozzle
19 Window wiper
20 Steam pistol
21 Steam switch on the connecting head
22 Lock ON or OFF/LOCK

Unpacking the Device

• Remove the main device and accessories from the box.
• Also remove any packaging materials that may be present.
• Check the scope of delivery.

Initial Operation

Filling up the Heating Boiler before Use!
Before the tank cap is opened it must be ensured that the device
is not under any pressure. Please proceed as follows:
1. Remove the plug from the socket.
2. Turn the lock (22) on the steam pistol (20) to ON (Fig. B1).
3. Press the steam switch (21) on the steam pistol (Fig. B2).
Point the steam nozzle at a surface which is allowed to
become wet.
NOTE:
After prolonged periods of non-use it is normal for a small
quantity of condensation to come out of the steam pistol at
first.
WARNING:
• If the device is still warm after an interruption to its
use there is a danger of injury!
• Please open the safety lock (6) only when no more
steam comes out of the nozzle.
4. Turn the lock in an anticlockwise direction.
NOTE:
For your protection the safety lock has a release device. If
the pressure in the kettle is still too high, this release device
prevents it from being opened.
5. Shake any residual water out of the kettle (7). Fill fresh-
water from the measuring beaker (15) into the kettle. Take
care of water splashes that might come out of the boiler. In
order to avoid water spray, please use the funnel supplied
(Fig. E). The water should be filled in slowly.
CAUTION:
Do not overfill! Max. water capacity: 1.5 litres.
• Do not use condensation from a tumble dryer (chemical
residues)! This is not distilled water!
6. Retighten the safety lock (6) in a clockwise direction.
Attachment of the Individual Accessories
It is possible to attach the individual nozzles directly to the
steam pistol (20) of the hose (1):
• Plug the adapter (14) onto the steam gun until it clicks into
place.
• To detach the adapter again, press the button on the steam
gun.
• Keep the button pressed and pull out the adapter.
Or extend the nozzle attachments with one or two extension
tubes (8):
• Please insert the sections of the 2-part extension tube one
inside the other until it locks into place (Fig. G). Then attach
it to the steam pistol (20).
• Attach the floor brush (18) to the extension tubes: press the
jointed adapter (17) on to the floor brush and turn it tightly
through 180°.
• If you would like to use the non-woven cloth, attach it to the
floor brush with the help of the clips (Fig. H).
• In order to release the extension tube, please press the
button on the steam pistol.
NOTE:
Various attachments can only be used in conjunction with the
adapter (14). Check that everything is properly connected!
Nozzle Adapter Use
Floor brush Jointed •
(18) adapter (17) •
Round with adapter •
brushes (11) (14)
•
High-pres- with adapter •
sure nozzle (14)
(12)
Window with adapter •
wiper (19) (14)
WARNING: There is a danger of injury!
Never attach or remove the accessories if the steam switch
(21) is pressed in! Wait until the device has cooled down.
Electrical Connection
• Before inserting the plug into the socket. Make sure that the
mains voltage to be used matches that of the device.
You can find this information on the nameplate.
• Connect the device to a duly installed 230 V/50 Hz protective
contact socket.
for large floor surfaces (Fig. J)
with non-woven cloth: for
sensitive surfaces (Fig. K)
for joints, fittings, grill grid
etc or
for difficult-to-access areas
(Fig. I and L)
for concentrated, high
steam pressure (Fig. M)
for windows or shower parti-
tions
31