Herunterladen Inhalt Inhalt Diese Seite drucken

Troubleshooting; Initial Use - Steinbach 049100 Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
EN
 INTEX special adapter (not included): INTEX special adapter item
No.: 040934. This is needed on large INTEX pools which have
swimming pool hoses with gate valves. Fig. 11,12
Model 049110 Speedsolar solar collector deluxe
Connection between solar collector and pool
For pools with a Ø 32 mm or Ø 38 mm swimming pool hose, follow
the instructions below:
Attach the hose to the return connector on the underside of
the solar collector.
Use a hose clip to connect the hose to the return connector
(see Fig. 13)
A: Pool return hose
B: Reduction fitting, if required
C: Hose clip
D: Return connector
For large INTEX pools (which have swimming pool hoses with gate
valves), follow the instructions below (Fig. 14):
Connect the INTEX special adapter and the O ring with the
return connector. Make sure the O ring is in the INTEX spe-
cial adapter.
Screw on the pool hose with the INTEX special adapter
Make sure that the seal between the hose and the INTEX
special adapter is correctly inserted.
A: INTEX special hose
B: INTEX special adapter
C: O ring
D: Return connector
E: Flat seal
Correct positioning of the solar collector
Attach both legs to the underside of the device and adjust position
according to the sun. Make sure the surface is stable and level.
The device should be assembled as shown in Fig. 15.
A: Swimming pool hose to the pool
B: Swimming pool hose from the filter / pump
C: Return connector
D: Connector flow
Make sure that all hose connections are watertight and the hose is
not kinked or have any sharp corners. It the hoses are not watertight,
check whether the O rings are correctly positioned and all connec-
tions are screwed together firmly. Do not over-tighten the hose clips
(15kg torque).
Connecting several collectors:
If you would like to increase the heating power, you can connect
several collectors together. For this you will need a additional swim-
ming pool hose Ø 32/38 mm. (Included with model 049110)
We recommend connecting a maximum of 2 collectors, depending
on the power of your filter unit.
We definitely recommend use of a bypass set (Fig. 18) Item No.
60045
Not only does this help optimal control of heat output, it also
helps targeted control of the water flow rate, depending on the
power of the filter unit.
4

Initial use

Once the solar collector is assembled and the hoses are connected
to the filter pump and the pool, open the water supply and ensure
that water is flowing through the hose. Then turn on the filter system.
Air bubbles will rise from the inlet nozzle in the pool. This happens
as the air is expelled from the solar collector. If this continues for
Speedsolar Sonnenkollektor | 2015_V1
more than 2-3 minutes, check the tightness of the connections in
your system.
Please note: Cover your pool overnight to avoid loss of heat.
5
Trouble shooting
Problem
Cause / Solution
 Make sure that water is flowing through
The
pool
does
not
warm up.
the hoses.
 Has it been sunny enough?
 Exploit the maximum amount of sunlight
and increase the running time of the filter
pump.
 Cover your pool overnight to avoid loss of
heat.
 It is possible that you may need several
solar collectors.
 Check the filter system and ensure that
No bubbles appear af-
ter the equipment has
water from the pool is flowing through
been attached to the
the filter pump, then through the solar
pump.
collector and finally through the connect-
or hose back to the pool.
 Check the connector hoses for any dam-
Air bubbles come out
of the pool return after
age.
the pump has been
 Check that the hose clamps have been
turned on.
properly tightened.
Water escaping.
 Check the seals in the system of pipes.
 Check whether you have tightened the
hose clamps tightly enough.
 Check the connector hoses for any
cracks.
6
Service
For technical information, if any parts are missing, or in the event of
a complaint, please contact our customer service department direct-
ly:
Steinbach Vertriebs gmbH
Aistingerstrasse 2, 4311 Schwertberg, Austria
e-mail: service@steinbach.at
www.steinbach.at
Page 5 of 30

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

049110

Inhaltsverzeichnis