Product Familiarisation; Intended Use; Unpacking Your Tool - Silverline 798866 Bedienungsanleitung

798866
Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and must
be repaired
c) Disconnect the plug from the power source and/or the battery pack
from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained users
e) Maintain power tools. Check for misalignment or binding of moving
parts, breakage of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed. Use of the power tool for operations different from
those intended could result in a hazardous situation
Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power
tool is maintained
Spray Gun Safety
Dangerous environment
• Ensure there is adequate clear space around the work area. Only use spraying
tools in a well-ventilated area or a specialist spray booth. Be aware that air
hoses can present a trip hazard; always lay hoses in a way that minimises
hazards
Protect your eyes
• Always wear safety goggles or safety glasses
Protective clothing
• Always wear appropriate protective equipment including but not limited to
overalls, gloves, facemask etc
• It is the user's responsibility to ensure that other persons in the vicinity of the
work area are also equipped with the appropriate protective equipment.
Use of spray guns
• Do not aim a spray gun at people or animals!
• When spraying keep away from heat and naked flames!
WARNING: Solvents and paints are harmful and can even be toxic. Some
solvents and paints are extremely flammable. Handle with care, according to the
manufacturer's recommendations. Store solvents and paint in sealed, leak proof
containers made of a material that is chemically resistant to the specific solvent.
Always wear suitable protective equipment and dispose of solvents and paints, as
well as contaminated items, as special waste, according to laws and regulations.
WARNING: Solvents that are chemically based on halogenated hydrocarbon, like
trichloroethane and methylene chloride 1,1,1, may cause chemical reactions in
combination with aluminium and galvanised or hot galvanised components, and
may therefore represent a potential explosion hazard.
WARNING: When spraying coating materials, dangerous vapours or aerosols,
which are detrimental to your health, are produced. Please read all labels
and safety instructions carefully, and observe all indicated instructions and
recommendations. In case of doubt, please ask the material supplier. Use
respiratory protection when spraying. The respiratory equipment used must
be suitable for the material in use and adapted to the degree of the vapour
concentration. When spraying paint, use respiratory equipment independent of the
ambient atmosphere, or equipment with filter combination A1/A2-P2. Ensure a
sufficient protection of your skin during all spraying and cleaning procedures. Wear
appropriate protective clothes and use suitable protective skin ointments.
WARNING: DO NOT spray acids, caustic solutions, removers and similar
substances.
500W HVLP Paint Sprayer

Product Familiarisation

1 Nozzle Assembly Cap
2 Spray Gun
3 Air Volume Adjuster
4 Air Filter Compartment
5 Shoulder Strap Mounts
6 On/Off Switch
7 Air Outlet
8 Air Hose
9 Turbine Unit
10 Shoulder Strap
11 Viscosity Test Cup
12 Paint Container
13 Trigger
14 Air Cap
15 Spray Pattern Adjusters
16 Nozzle

Intended Use

This paint sprayer is for applying paints and coatings to various surfaces and
should not be adapted for other uses or liquids that are not normally sprayed.
Ensure the manual is fully read before using this tool.

Unpacking Your Tool

• Carefully unpack and inspect your tool. Familiarise yourself with all its features
and functions.
• Ensure that all parts of the tool are present and in good condition. If any parts
are missing or damaged, have such parts replaced before attempting to use
this tool.
www.silverlinetools.com
5