t6t
I
r7l
ll>
6.
OPERATING
THE
E
426 CD
PLAYER
Front panel
of the
E
426 CD player
[3]
Power
Turns
the CD
player
on or
switches
it
to
standby
mode.
14,51
<
,
>
Plays
the
current
or the
next track
from
the
beginning.
Pressing
the
<
key
twice
within
one second takes
you to the
begin-
ning
of the
previous
track.
For aud
i
ble
fast-forward/fast-
reverse,
press
and hold the < or
>
key.
The
function
starts
with
steps
of
I
second
and accelerates later
to
steps
of
5
seconds.
stop,
Stops play, shows
total
playing time.
play,
pause
Plays
CD
or
suspends
play.
[27] UNBALANCED OUT
Single-ended analogue
audio outputs, left
and
right
(RCA).
T28,291OUTPUT
DIGITAL
All
information
that
is
stored
on the CD
is
fed to
the
two
digital outputs
(RCA,
BNC).
The
outputs
are electrically insulated
from
the
circuitry by
means
of
a transformer.
I24lAC
POWER
AC
power
connection
power
switch
mains fuse
Programming functions
The CD player allows
you
to
compile
a
playlist compris-
ing
up
to
20
tracks
of the
same
CD.
For
programming,
use
the controls on
the unit
or
the
RC
28
remote
control.
Enabling
the
repeat
function
a
a
Press
and hold
the
mode key
[8]
for
about
5
sec-
onds,
<REP
ONE,
is
shown
on
the
display.
Select
the
<REP
DISC> or
<SHUFFLE>
function
or
the program-
ming
function
by
pressing
the
mode key
IBJ.
<REP
ONE>
plays
the
current
track
repeatedly,
<REP
DISC> plays
the whole
disc repeatedly,
and
<SHUF-
FLE>
plays
the tracks
in
random
order.
Press
the
lltr
key
[7] to
enable
the
selected
function.
Press
the
I
key
t6J
twice
to
return
to
normal opera-
tion
mode
of the
CD
player.
Enabling
the
programming function
.
Press
and hold
the
mode key
[8i for
about
5
sec-
onds,
<REP
ONE>
is
shown on
the
display.
.
Press
and hold
the
mode
key
t8J
until the
track
number
is
replaced
by
two
lines
and
<PROG> flashes.
Now,
you
can
enter the
first
programme
step.
Entering a programme
step
Press
the
keys
marked
<,>
14,51
to
select
the
de-
sired
track
(e.9.
04)
for
step
1.
The display shows
the
selected
track
number
(04),
the
number
of
programme steps
(first
two
digits),
and the
total
playing time
of the
programme
(min./
sec.):
e.g.
<01
03:54>.
Simultaneously,
<PROGn
flashes.
Press
the mode
key
[8]
to
store
the programme
step,
again
the track number
is
replaced
by
two
lines.
Press
the
keys
marked <
,
>
14,51
to
select
the
next
track.
Press
the
mode key
[8J
to
store
the
programme
step.
Follow this
procedure
to
enter up
to 20
programme
steps.
The maximum programme playing
time
is
99
min-
utes.
[8]
mode
Press
momentarily:
Cycles
through
the four time
display
modes: remaining time of the current track,
elapsed
time of the
whole CD,
remaining
time of the whole
CD, and
elapsed
time
of
the
current track. The
time
modes
of
the
CD are
shown
by a corresponding symbol
on
the
display.
Press
and hold
for
about
5
seconds:
Switches
to the
programming functions.
[10] Open/Close
Opens
CD
compartment
or closes CD
com-
partment and
plays
CD.
t9l
display
Shows
track number and
various
time
in-
dications.
See
programming functions.
Operating the
E
426
CD
player
with
the
lR remote
con-
trol
[1] off
t3l
cD
[7] <<
,
>>
Switches
the
CD
player
off.
Switches
the entire
Exception
hi-fi
system
off
if
the
components
are interconnected.
Switches
the CD
player
on and
plays
the
first track
of the
CD.
lf ihe
CD player
is
interconnected
with the
E
450 amplifier via
Revox
Link, the ampli-
fier
automatically
switches on and
to
CD
if
in
standby mode
or
to
CD
if
already
in
operation.
Aud
i
ble
I
asl-f orw
ar
d
/fast-
reverse.
[8]<,>
Track
selection.
Rear
panel
of the
E
426
CD player
[25]
Revox
Link
Connectors
for
interconnected operation
with the
E
450
amplifier.
[26]
BALANCED
OUT
Balanced
analogue
audio outputs, left
and
right
(XLR).