Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Jäger Direkt GmbH & Co. KG • Hochstraße 6 • 64385 Reichelsheim • Tel.: +49 (06164) 930050 • Fax: +49 (06164) 930069 • e-mail: info@jaeger-direkt.com • Internet: www.opus-schalter.de
Installation and operating instructions
OPUS RADIO PLUS actuator two-way FM
for RADIO PLUS transmitters
Art.no.: 561.312
1. Description
Different consumers such as incandescent lamps, high-
voltage halogen lamps, electronic ballast and inductive
loads can be switched with the output 1 (channel 1) and
output 2 (channel 2) of the actuator.
The Opus
®
-Radio Plus actuator is controlled by radio signals
from Radio Plus transmitters. Each transmitter can simultan-
eously control an unlimited number of actuators.
The transmitters have a fixed address and must be assigned
on a actuator (max. 32 transmitters).
The memory of each actuator is empty when delivered.
Function 1 (two-button function) is preset by default in the
actuator of a freshly assigned transmitter.
The actuator 's function can be changed by programming
to respond to any assigned transmitter (see Point 6).
2. Mounting
561.312
FUNK Plus
Schaltaktor 2fach Up
CLR/MODE
1
2
µ
µ
230V~
50Hz
LRN/SET
L max.2x500W
1
L 2
N N
N N 1 L 2
Learn mode:
LED = red
Function programming:
LED = green oder orange
N
L
Mounting and set-up may only be carried out by an
authorised professional.
All works may only be performed once the mains power
supply 230V/50Hz~ has been switched off. Mounting must
adhere to the valid laws, standards and regulations.
The supply line may only be fused with a fuse or circuit
breaker (max. 10A).
For programming, the actuators must be connected to the
mains power supply. The programming is retained even in a
power failure.
NEVER mount the Radio Plus transmitter or actuator in a
metal housing or directly next to large metal objects.
It is also not advisable to mount the actuators on the floor or
close to the floor.
The following points must be observed:
- the valid laws, standards and regulations
- the best available technology at the time of installation.
- the operating instructions of the Radio Plus-modules.
- the fact that operating instructions can only contain general
guidelines and that these must be considered in the context
of a specific system.
Caution!! The Radio Plus-modules must not be used with
devices, which could affect human health or safety, or en-
danger humans, animals or material assets.
561312-Rev01_070122.pdf
GB
3. Technical data
Transmission frequency 868.3 MHz
Power supply
Fusing the supply lines
Consumer connection
data per channel
Ambient temperature
Storage temperature
Protection level
4. Assigning or deleting Radio Plus transmitters
Opus
®
-Radio Plus transmitters can be assigned or deleted in
the learn mode of the actuator.
Learn mode is activated by pressing the LRN/SET button
and the channel 1 is active (LED flashes red).
If the LRN/SET button is pressed a second time, channel 2
becomes active (LED 2 flashes red).
A Radio Plus transmitter can be assigned on both channels!
If a button of the transmitter that is to be assigned is pressed
once in learn mode and recognized by the actuator (LED on),
the transmitter has been assigned.
To delete a assigned transmitter, the channel on which it was
CLR/MODE-button
assigned must be selected!
Parameter setting
If a transmitter has been assigned on both channels, then it
LRN/SET-button
must also be deleted on both channels (if this is desired)!
Learn mode and
If a button of an already assigned transmitter is pressed once
Function
and recognized by the actuator (LED off), the transmitter has
programming
been deleted.
Caution!! If the button off a transmitter is pressed repeatedly
the transmitter will be alternately assigned or deleted!
After a Radio Plus transmitter has been assigned or deleted
the actuator returns to learn mode for channel 1 or channel 2
and other transmitters can be assigned or deleted.
When no button of an Radio Plus transmitter is pressed, the
actuator leaves the learn mode after approx. 30s independently.
Press the LRN/SET
button briefly
2x
Learn mode channel 1
(LED flashes red)
Press the LRN/SET
button briefly
Learn mode OFF
(LED off)
Function 1 (two-button function) is preset by default in the
actuator of a freshly assigned transmitter.
If desired, the actuator's function and its parameter can be
changed by function programming (see Point 6) for each
assigned transmitter.
5. Deleting all assigned transmitters
Press the CLR/MODE button and hold it down for approx. 2s.
During this time, the memory is completely deleted (delivery
status). Then, the actuator is in learn mode (LED flashes red).
Press the CLR/MODE
button for longer
All assigned
transmitters deleted
Learn mode channel 1
(LED flashes red)
230 V~ / 50 Hz
Circuit breaker or fuse
(max. 10 A)
Incandescent lamp: 500 W
HV-halogen lamp:100 W
Inductive load: 100 VA
Electronic ballast load: 1 unit
-20° to +40 C
-40° to +85°C
IP 20
Assign/delete transmitter
Press a button of the
transmitter once
Transmitter assigned
(LED 1-2 on)
Actuator function 1
Transmitter deleted
(LED 1-2 off)
s. Point 4
6. Function programming
The Radio Plus actuator's function and its parameter can
be changed by function programming each assigned Radio
Plus transmitter (see Point 4).
Function programming is activated by pressing an holding the
LRN/SET button until confirmed (LEDs flash green rapidly).
Function programming can be manually terminated by
activating the CLR/MODE button.
Without activating the button on a transmitter, the actuator will
terminate function programming automatically after about 30s.
If function programming is active, a button of the transmitter
must be pressed for recognition, for which the function of
the actuator is to be changed.
Once the transmitter is recognized by the actuator, the actuator's
active channel will be the one on which the transmitter was
assigned (LED 1 or LED 2 flashes orange).
The number of times the LED flashes corresponds to the
actuator's current function. This function can then be changed
by the number of times that the LRN/SET button is activated
(e.g. pressing LRN/SET twice = Function 2).
Press the LRN/SET
button for longer
Function programming
(LEDs flash green rapidly)
Recognition of transmitter
Press a button of the transmitter
Channel 1 or 2 is active
(LED flashes orange)
number of flashing = function
Press the LRN/SET button to
select the function 1-8
number of actuations = function
Press the CLR/MODE
button briefly
Parameter setting
Channel 1 or 2 is active
(LED flashes green)
number of flashing = parameter
Press the LRN/SET button to
select the parameter
number of actuations = function
The parameter setting is accessed in function programming
by activating the CLR/MODE button.
Afterwards the channel is active, on which the transmitter
was assigned (LED 1 or LED 2 flashes green).
Parameter setting can be manually terminated by activating
the CLR/MODE button.
The number of times the LED flashes corresponds to the
parameter currently set for the actuator's current function.
This parameter can then be changed by the number of times
that the LRN/SET button is activated
(e.g. pressing LRN/SET twice = Parameter 2).
Caution!! If a Radio Plus transmitter has been assigned on
both channels, the functions and parameters of both
channels of the Radio Plus actuator can be changed!
If channel 1 is initially active (LED 1 flashes) for function
programming then the function and parameter for channel
1 can be changed.
When the CLR/MODE button is subsequently pressed,
channel 2 will become active (LED 2 flashes) for function
programming so that the function and parameter for channel
2 can also be changed.
Idle state
(LED off)
Press the CLR/MODE
button briefly
GB - 1
Werbung
