Electrical Safety; Safety Instructions - Mantis 8110-00-38 Gebrauchsanweisung

are jamming less often and are easier to guide.
g) Use power tools, accessories, add-on tools,
etc. in accordance with these instructions and
in the way described for the respective type
of tool. You should also consider the working
conditions and the work to be carried out. The
use of power tools for purposes other than those
intended for the respective tool may result in dan-
gerous situations.
5) Service
a) Have the power tool serviced by qualified tech-
nical personnel only; repairs should be carried
out using only original spare parts. This will
ensure the safe operation of the power tool.

Safety Instructions

Read the operating instructions and act ac-
cordingly. Keep it for general use. Comply with
the safety information and the warning on the
appliance.
• The machine must be assembled correctly before use.
• Before inserting the plug in the electric socket, make
sure that the socket ratings are correct and corre-
spond to those indicated on the rating label on the
appliance.
• Never move the machine by pulling at the cables.
• Always disconnect the machine from the electric sup-
ply before transporting it to other places.
• Always switch off the machine before disconnecting
any plug and socket connector or extension cable.
• Keep away from children and pets. All onlookers
should keep a safe distance from the machine when
it is in use.
• The user is responsible for third parties while working
with the machine.
• Be careful never to throw snow towards people or
cars, and never allow anyone in front of your snow
shovel.
• People not acquainted with the operating instructions,
children, juveniles who have not yet reached the mini-
mum age for using this machine, and people under
the influence of alcohol, drugs or medication are not
allowed to use the machine.
• Only use the machine for its designed purposes.
• Always use the machine with the discharge chute
attached.
• Keep hands and feet away from all rotating and mov-
ing parts.
• Never put your hand in the discharge chute or near the
auger to remove snow, sticks or other debris. Blocked
auger can "spring back" when cleared and may cause
personal injury, even with the machine stopped.
Always use an object such as a long stick or shovel
handle to clear blockages.
• Wear safe, sturdy, nonskid footwear. Ensure that you
have a good stand, especially on slopes.
• Wear safety glasses, and avoid any loose-fitting cloth-
Contact us at www.mantis.uk.com
ing that could get caught in moving parts. Be careful
of long hair.
• Only work in daylight or sufficiently good artificial light.
• In order to start the machine, the auger must be com-
pletely free to move.
• The use of the machine is only permitted if the safety
distance provided by the guide bar is complied with.
• Always hold the handle bar firmly and walk, never run.
• Do not overload the machine by attempting to clear too
much snow at once.
• Slow down and turn corners slowly.
• Caution! Auger does not stop immediately after
switching off.
• Always switch off the machine, disconnect the plug
and wait until the auger stops before carrying out
maintenance or cleaning work.
• Use caution when cleaning or performing mainte-
nance on the machine. DANGER! Watch your fin-
gers! Wear gloves!
• It is forbidden to move or modify any of the electrical
and mechanical safety devices.
• The snow can sometimes hide objects that might clog
the chute, or otherwise cause damage. Clear the area
of doormats, sleds, boards, wires and other debris.
• If the machine strikes a foreign body, examine the ap-
pliance for signs of damage and carry out any neces-
sary repairs before restarting and continuing to work.
• If the machine should start to vibrate abnormally,
switch off the motor and check for the cause immedi-
ately. Vibration is generally a warning of trouble.
• The machine should be checked carefully before use.
You should only work with an machine that is in good
condition. If you notice any defect on the machine that
may cause danger to the operator, do not operate the
machine until defects are rectified.
• Replace worn or damaged parts for safety. Use only
original spare parts. Parts not produced by manufac-
turer may cause poor fit and possible injury.

Electrical Safety

• Design of the connection cable according to IEC
60245 (H 07RN-F) with a core cross-profile section
of at least
2
- 1.5 mm
for cable lengths up to 25 m
2
- 2.5 mm for cable lengths over 25 m
• Long and thin connection lines result in a potential
drop. The motor does not reach any longer its maximal
power; the function of the device is reduced.
• Plugs and coupler outlets on connection cables must
be made of rubber, non-rigid PVC or other thermoplas-
tic material of same mechanical stability or be covered
with this material.
• The connector of the connection cable must be
splash-proof.
• When running the connection line observe that it does
not interfere, is not squeezed, bent and the plug con-
nection does not get wet.
• Wind off completely the cable when using a cable
drum.
11