Safety Instructions - Mantis 8120-00-38 Gebrauchsanweisung

IMPORTANT!

Safety Instructions

GENERAL SAFETY INSTRUCTIONS
Warning: Read all instructions. Failure to follow all instruc-
tions listed below may result in electric shock, fire and/
or serious personal injury. The term "power tool" in all of
the warnings listed below refers to your mains-operated
(corded) power tool.
SAVE THESE INSTRUCTIONS
1) WORK AREA
a) Keep work area clean and well lit. Cluttered and dark
areas invite accidents.
b) Do not operate power tools in explosive atmosphere,
such as in the presence of flammable liquids, gases,
or dust. Power tools create sparks which may ignite
the dust or fumes.
c) Keep children, pets and bystanders away while from
work area. Be aware that the normal noise of the
machine when turned on may make it difficult for
you to hear approaching people.
2) ELECTRICAL SAFETY
a) Electrical plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of
electric shock.
b) Avoid body contact with earthed or grounded sur-
faces such as pipes, radiators, ranges, and refrigera-
tors. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet snow.
Water entering a power tool will increase the risk
of electric shock.
d) Do not abuse the cord. Never use the cord for car-
rying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the
risk of electric shock.
e) When operating a power tool outdoors, an extension
cord suitable for outdoor use and an RCD device
must be used. Use of a cord and RCD suitable for
outdoor use reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are doing and use com-
mon sense when operating a power tool. Do not
use a power tool while you are tired or under the
influence of drugs, alcohol, or medication. A moment
of inattention while operating power tools may result
in serious personal injury.
b) Use safety equipment. Always wear eye protection.
Safety equipment such as a dust mask, non-skid
safety shoes, hard hat, or hearing protection used for
appropriate conditions will reduce personal injuries.
8
Electric Snow Thrower Operator's Manual
c) Avoid accidental starting. Ensure the switch is in
the off-position before plugging in. Carrying power
tools with your finger on the switch or plugging in
power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning
the tool on. A wrench or a key that is left attached
to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing, and gloves away from mov-
ing parts. Loose clothes, jewelry or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust
extraction and collection facilities, ensure that these
are connected and properly used. Use of these
devices can reduce dust-related hazards.
4) POWER TOOLS USE AND CARE
a) Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate from which
it was designed.
b) Do not use the power tool if the switch does not turn it
on and off. Any power tool that can not be controlled
with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts, and
any other conditions that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
f) Keep cutting tools sharp and clean. Properly main-
tained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc.,
in accordance with these instructions and in the
manner intended for the particular type of power
tool, taking into account the working conditions and
the work to be performed. Use of the power tool for
operations different from intended could result in a
hazardous situation.
5) SERVICE
a) Have your power tools serviced by a qualified re-
pair person using only identical replacement parts.
This will ensure that the safety of the power tools
is maintained.