Description; Assembling; Guide Bar; Motor Housing - Mantis 8110-00-38 Gebrauchsanweisung

• Do not drive the device across the extension cable.
Make sure that it is behind you in a secure position.
Place the cable on a path or area that has already
been cleared of snow.
• Do not use the cable for purposes for which it is not
meant. Protect the cable against heat, oil and sharp
edges. Do not use the cable to pull the plug from the
socket.
• Protect yourself against electric shocks. Avoid touch-
ing earthed parts with your body (e.g. pipes, heating
apparatus, cookers, fridges etc.).
• Regularly check the extension cables and replace
them if they are damaged.
• Do not connect a damaged cable to the mains. Do
not touch a damaged cable before it is disconnected
from the mains. A damaged cable may cause contact
with live parts.
• Do not use any defective connection cables.
• When working outdoors, only use extension cables
especially approved and appropriately labeled for
outdoor use.
• Do not set up any provisional electrical connections.
• Never bypass protective devices or deactivate them.
• Only hook up the machine by means of a fault-current
circuit breaker (30 mA). The electrical connection
or repairs to electrical parts of the machine must be
carried out by a certified electrician or one of our
customer service points. Local regulations - especially
regarding protective measures - must be observed.
Damaged mains leads must be replaced by the manu-
facturer or one of their service workshops or a similar
qualified person to prevent dangers.
Repairs to other parts of the machine must be carried
out by the manufacturer or one of his customer service
points. Use only original spare parts, accessories and
special accessory parts. Accidents can arise for the user
through the use of other spare parts. The manufacturer
is not liable for any damage or injury resulting from such
action.

Description

(Fig. 1)
1 Main plug
2 Lock off button
3 Switch trigger
4 Handle
5

Front handle

6 Guide bar lower section
7 Discharge chute
8 Snow deflector
9 Auger

10 Motor housing

11 Adjust knob
12
Electric Snow Shovel Operator's Manual

Assembling

Guide bar (Fig. 1)
Slide the lower section (6) into the upper tube (4) of
the handle. Line up holes on each tube, and make sure
that the internal cable (A) does not pass the mounting
holes. Fix two sections firmly with the supplied screw
and wing nut.
Motor housing (Fig. 1)
• Connect socket (B) to the plug on the motor housing.
• Fasten the housing using the 4 supplied ST4.2x30 screws.

The adjust knob

• Fasten the adjust knob by supplied ST4.2x30 screws.
(Fig. 1)
• Pull the adjust knob up, you can change the snow
deflector orientation. (Fig. 2)
Front handle
Loosen the knob and lift up the handle bar to the opera-
tion position. (Fig. 3) Adjust the height of the handle to
a safe and comfortable position and fix it by the knob.
Connection the mains (Fig. 4)
Loop the extension cord and feed it through the rear
handle. Rest the cord around the cord hook. This will help
prevent you from disconnecting the extension cord from
the product during operation. Warning! Do not handle the
plug or the appliance with wet hands or while standing
in water.
DANGER! Electric shock causes series injury
and death!

Starting

Intend use

This appliance is only intended for sweeping of snow on
steps, patios and decks in private domestic and hobby
gardens. It is not designed for use in public areas, parks,
sports areas, and in agriculture and forestry. Using the
application only on hard, flat surfaces free of sand, stone
and debris, wires and any other objects. For any other
purpose is considered incorrect and unapproved. The
manufacturer is not liable for any damage or injury result-
ing from such use. The user is entirely responsible for
any associated risks.
On/Off switch (Fig. 5)
Warning! The auger starts rotation immediately
after switch on! Keep hands and feet away
from auger.
To switch ON, hold the appliance firmly with two hands
and press the Safety lock off button (2) while pressing
the On/Off switch trigger (3). Keep the switch trigger
held while releasing the button. To stop the appliance,
release the switch trigger and it automatically returns to
its start position.