Telefunken XF49G511 Bedienungsanleitung Seite 47

Switching On/Off
To Switch the TV On
Connect the power cord to a power source such as a
wall socket (220-240V AC, 50 Hz).
Note: Main switch position may differ depending on the model.
To switch on the TV from standby mode either:
• Press the Standby
numeric button on the remote control.
• Press the middle of the side function switch on the
TV in.
To Switch the TV Off
Press the Standby button on the remote control or
press the middle of the side function switch on the
TV in and hold it down for a few seconds, the TV will
switch into standby mode.
To power down the TV completely, unplug the
power cord from the mains socket.
Note: When the TV is switched into standby mode, the standby
LED can blink to indicate that features such as Standby
Search, Over Air Download or Timer is active. The LED can
also blink when you switch on the TV from standby mode.
First Time Installation
When turned on for the first time, the language
selection screen is displayed. Select the desired
language and press
the installation guide, set your preferences using the
directional buttons and
On the second screen set your country preference.
Country
Depending on the
to set and confirm a PIN at this point. The selected PIN
cannot be 0000. You have to enter it if you are asked
to enter a PIN for any menu operation later.
You can activate Store Mode
This option will configure your TV's settings for store
environment and depending on the TV model being
used, the supported features of it may be displayed on
the side of the screen as an info banner. This option
is intended only for store use. It is recommended to
select Home Mode for home use. This option will be
available in Settings>System>More
be turned off/on later. Make your selection and press
OK to continue.
Depending on the model of your TV and the country
selection Privacy Settings menu may appear at
this point. Using this menu you can set your privacy
privileges. Highlight a feature and use Left and
Right directional buttons to enable or disable. Read
the related explanations displayed on the screen
for each highlighted feature before making any
changes. You can use
scroll up and down to read the entire text. You will
be able to change your preferences at any time
later from the Settings>System>Privacy Settings
button, Programme +/-
OK . In the following steps of
OK button.
selection you may be asked
option in the next step.
menu and can
Programme +/- buttons to
menu. If the
Network/Internet Settings screen will be skipped
and not displayed. If you have any questions,
complaints or comments regarding this privacy
policy or its enforcement, please contact by email at
smarttvsecurity@vosshub.com.
Highlight Next
control to continue and the Network/Internet Settings
or a
menu will be displayed. Please refer to Connectivity
section to configure a wired or a wireless connection.
If you want your TV to consume less power in standby
mode, you can disable the Wake On option by setting it
as Off. After the settings are completed highlight Next
OK button to continue
and press
On next screen you can set broadcast types to be
searched, set your encrypted channel searching
and time zone (depending on the country selection)
preferences. Additionally you can set a broadcast
type as your favourite one. Priority will be given to the
selected broadcast type during the search process
and the channels of it will be listed on the top of the
channel list. When finished, highlight
OK to continue.
About Selecting Broadcast Type
To turn a search option for a broadcast type highlight
it and press
option will be checked. To turn the search option off
clear the checkbox by pressing
focus on the desired broadcast type option.
Digital Aerial:
is turned on, the TV will search for digital terrestrial
broadcasts after other initial settings are completed.
Digital Cable: If D. Cable broadcast search option
is turned on, the TV will search for digital cable
broadcasts after other initial settings are completed.
A message will be displayed before starting to search
asking if you want to perform cable network search. If
you select Yes
or set values such as
Search Step on the next screen. If you select No
and press OK
Frequency and Search Step on the next screen.
When finished, highlight
to continue.
Note: Searching duration will change depending on the
selected Search Step
If Satellite
Satellite: broadcast search option is turned
on, the TV will search for digital satellite broadcasts
after other initial settings are completed. Before
satellite search is performed some settings should be
made. Antenna Type menu will be displayed first. You
can select Antenna Type
Cable or DiSEqC switch
buttons. After selecting your antenna type press
see the options to proceed. Continue Transponder
list and Configure LNB
English - 10 -
Internet Connection
and press OK button on the remote
.
OK . The checkbox next to the selected
OK
If D. Aerial broadcast search option
and press OK you can select
Frequency, Network ID
you can set Start Frequency Stop
Next and press
.
as Direct,
by using Left or Right
options will be available. You
option is disabled
Next and press
after moving the
Network
and
,
OK button
Single Satellite
OK to
,