BOMANN TDC 321 CB Bedienungsanleitung Seite 36

6. To remove wrinkles on towels, handkerchiefs, or napkins,
hang them over a rod or a towel holder and smooth them
gently.
7. Heavy fabrics require repeated steaming.
8. To eliminate larger wrinkles, treat both sides of the fabric
with steam.
9. The brush attachment can also be used to remove larger
wrinkles.
When you have finished
1. Set the On/Off switch to "OFF". The pilot light in the switch
goes out.
2. Unplug the power cord.
3. Wrap the steam hose once around the telescopic tube and
set the nozzle into the holder.
4. Loosen the two upper clamps of the telescopic tube and
collapse the telescopic tube.
5. Roll the unit to a suitable storage place.
cleaning
WARNING:
• Always remove the mains lead before cleaning!
• Wait until the machine has cooled down completely!
• Under no circumstances should you immerse the device
in water for cleaning purposes. Otherwise this might
result in an electric shock or fire.
cAUTION:
• Do not use a wire brush or any abrasive items.
• Do not use any acidic or abrasive detergents.
• Clean the casing with a slightly damp cloth.
Preparing for long-term storage
We recommend performing the following steps once a week.
When distilled water is used, cleaning is not required as often
and the life of the unit increases.
1. Disconnect the steam hose and the telescopic tube.
2. Place the unit over a drain.
3. Remove the water tank and empty it. Rinse the tank with
fresh water and empty it completely.
4. Empty the unit completely. Either remove the drain plug or
pour the water out of the unit.
Problem
No steam is put out and the pilot
light in the On/Off switch does not
light.
No steam is put out and the pilot
light in the On/Off switch is lit.
36
5. To rinse the unit, fill fresh water into the water inlet and the
6. Replace the tank on the unit.
7. Install the steam hose and the telescopic tube.
8. Wrap the steam hose once around the telescopic rod and
9. Loosen the two upper clamps of the telescopic tube and
10. Roll the unit to a suitable storage place.
descaling
A common problem with steam appliances are lime deposits
when hard water is used. Lime residue in the internal lines and
the heater can lead to intermittent steam discharge or in some
cases to a complete stop of steam output.
If you cannot use distilled water, we recommend that you
perform descaling once a month. Proceed as follows:
1. Disconnect the steam hose and the telescopic tube.
2. Place the unit over a drain.
3. Remove the water tank and empty it. Rinse the tank with
4. Empty the unit completely. Either remove the drain plug or
5. To rinse the unit, fill fresh water into the water inlet and the
6. Prepare a solution with 50 % vinegar and 50 % water. In
7. Pour this solution slowly into the tube
8. If the filled-in solution does not
9. Let the solution at for 40 minutes.
10. Empty the unit completely.
11. Rinse the hose connection as well as the water tank with
12. Connect the steam hose and the telescopic tube.
Troubleshooting
Possible cause
Mains plug not plugged in.
Mains circuit breaker tripped.
Lime deposits in the unit.
The water tank is empty.
hose connection and empty the unit completely.
set the nozzle into the holder.
collapse the telescopic tube.
NOTE:
To reduce or prevent lime deposits, we recommend the use
of distilled water.
fresh water and empty it completely.
pour the water out of the unit.
hose connection and empty the unit completely.
most cases, 2 cups of this solution will be sufficient.
connection of the unit (Fig. F), until the
water tank of the unit is about half full.
become visible in the inlet of the unit,
fill the hose connection completely.
Additionally, pour solution into the water inlet, until the water
tank of the unit is about half full.
fresh water, until all vinegar residue has been removed.
Remedy
Plug in the mains plug.
Close the circuit breaker.
Descale the unit.
Fill with water.