Using Megafilt - Bosch BSG8 Serie Gebrauchsanweisung

Figure
19
Grip the dust collector by the carrying
handle and remove it.
Figure
20
Press the latch in the direction of the
arrow to open the base and empty the
dust collector by pressing the lid lock
in the direction of the arrow.
If the base is very dirty (thick dirt) clean
this first e.g. by vacuuming using the
crevice tool.
(Fit dust bag in the vacuum cleaner
when you do this - see illustration 29)
Close the base.
Figure
21
Refit the dust collector into the
vacuum cleaner, position the carrying
handle at the side and close the dust
bag compartment lid.
!
Caution: The inside of the dirt
container may become scratched
with use and start to look opaque.
This does not, however, affect the
performance of the vacuum cleaner
in any way, i.e. it will continue to
function as normal.
Cleaning the permanent filters
and microfilters
When must the filters be cleaned:
If the vacuum cleaner is used until the
dust indicator lights up.
After any operating problem,
i.e. after a blockage is cleared.
At least every six months.
Figure
22
Unlock the filter holder by pressing in
the two lugs and open in the direction
of the arrow.
22
Figure
23
Remove the microfilters and
permanent filters and shake them
clean.
!
Caution: The washable white fleece
filter should be handwashed every
six months or after every time the
dust collector becomes completely
full, and should only be put back
after drying for about 24 hours.
Blockages
Removing a blockage in the dust
collector.
Figure
24
Unfasten the 4 snaplocks by pushing
them in the direction of the arrow and
remove the dust collector cover.
Loosen the blockage
e.g. with a screwdriver, and tap it out.
(Please fit dust bag into the vacuum
cleaner before vacuuming it out
- see Figure 29)
Figure
25
Put the dust collector cover back on
and push in the direction of the arrow
until you hear the 4 clasps lock into
place.
!
Caution: The microfilters and
permanent filters must be cleaned
after every blockage.
(see Figures 22 and 23).
en

Using MEGAfilt

®
filter bags
If necessary, a MEGAfilt
bag can be used instead of the dust
collector.
Figure
26
Open the dust bag compartment
cover (see Figure 18)
Remove the dust collector and fit thel
MEGAfilt SuperTEX dust bag.
®
Close the dust bag compartment
cover.
You have bought an extremely powerful
device. The highest suction setting is
therefore only recommended for heavily
soiled, short-pile carpets and hard floors.
The desired level of suction can be
adjusted to any level using the suction
regulator switch (see Figure 16).
Low suction range:
For vacuuming delicate fabrics, e.g.
curtains.
Middle suction range:
For daily vacuuming of lightly soiled
floors.
High suction range:
For vacuuming durable floor coverings,
hard floors and for heavily soiled
surfaces.
SuperTEX Replacing the MEGAfilt
dust bag
Figure
27
SuperTEX filter
®
If the dust bag change indicator lights
up brightly and uniformly when the
nozzle is lifted from the floor and the
vacuum is on its highest setting, you
should change the dust bag, even if it
is not yet full. In this case it is
essential to change the dust bag due
to the type of material it contains.
Turn the dust compartment locking
lever in the direction of the arrow to
open the dust compartment cover.
Figure
28
Seal the MEGAfilt
by pulling the locking tab and then
remove it.
Figure
29
Place a new MEGAfilt
bag in the holder and close the dust
bag compartment cover.
!
Caution: The dust bag compartment
cover will only close when the
MEGAfilt
textile filter or dust collector has
been inserted.
If the dust bag change indicator
continues to light up after the dust
bag has been changed, please
check whether the nozzle, pipe or
vacuum hose are obstructed.
en
SuperTEX
®
SuperTEX dust bag
®
SuperTEX dust
®
SuperTEX dust bag,
®
23