When The Work Is Done; Using The Dust Collector - Bosch BSG8 Serie Gebrauchsanweisung

Vacuuming with accessories
Figure
10
Pull the combination tool in the direction
of the arrow to remove it from the tool
holder.
a) Crevice nozzle
For vacuuming in crevices and
corners.
For difficult to get to places, the com-
bination tool can be extended in two
stages by pulling out the crevice
nozzle.
Extend the crevice nozzle to the
second stop until you can hear it
engage.
The crevice nozzle can be pushed
back in again by releasing the teles-
copic locking mechanism (pressing
it in the direction of the arrow).
b) Upholstery nozzle
For cleaning upholstery, curtains, etc.
c) Furniture brush. For window frames,
cabinets, profiles etc.
Fold the upholstery nozzle over in
the direction of the arrow.
To extend the brush ring, turn in the
direction of the arrow.
Before replacing combination tool
in the tool holder, retract the bush
ring and fold the upholstery nozzle
back.
11
Figure
Secure the drill dust nozzle to the
handle and then place against the wall,
so that the nozzle drill hole opening sits
directly over the hole to be drilled.
Select the lowest power setting and
then switch on the vacuum cleaner.
Suction holds the drill dust nozzle in
the required position. Depending on
the surface of the wall to be drilled it
may be necessary to readjust the
20
power to a higher setting to ensure
the drill dust nozzle is firmly attached.
Any fine particles are automatically
vacuumed up.
! Caution: The drill dust nozzle
should only be used in conjunction
with the dust collector since fine
drill dust can impair the function of
the dust bag.
Figure
12*
When stopping cleaning for a
moment, you can use the parking aid
at the back of the vacuum cleaner.
Slide the plastic lug on the tool
connector into the groove at the back
of the vacuum cleaner.
If your cleaner has the automatic
standby function, it will now switch
itself off.
=> Power indicator lights up "green".
* Depending on equipment
en

When the work is done

Figure
13
Switch the vacuum cleaner off and
unplug the power cord from the
mains.
Tug the power cord and let go. The
cable then rewinds automatically.
To reactivate or deactivate the cable
brake, quickly tug the power cord.
On vacuum cleaners with an
electronically actuated cable rewind,
the power cord automatically rewinds
when the machine is unplugged at the
socket.
If you do not want the power cord to
rewind completely (e.g. when
changing the plug), you can apply the
cable brake by pulling the power cord.
Figure
14
Press the adjusting button/sleeve in
the direction of the arrow to unlock
and collapse the telescopic tube.
Figure
15
To store or transport the vacuum
cleaner, use the storage aid on the
underside of the cleaner. Stand the
vacuum cleaner up on its end. Slide
the plastic lug on the floor into the
groove on the underside of the unit.
You have purchased a floor vacuum
cleaner which can vacuum up any type
of dry dirt and uses a dust collector and
MEGAfilt SuperTEX dust bags.
®
We recommend that you use
– the dust collector for dirt generated by
DIY in particular, such as sawdust.
– the MEGAfilt SuperTEX dust bags
®
mainly for everyday household
cleaning.

Using the dust collector

Figure
16
Set the power setting to maximum for
the best results when vacuuming.
We recommend that you reduce the
setting only when vacuuming very
delicate materials.
Emptying the dust filter
Figure
17
The dust collector should be emptied
every time the vacuum cleaner is used.
It must be emptied, however, as soon
as the dust indicator constantly lights
up bright red when the nozzle is lifted
from the floor and the setting is at its
highest.
Figure
18
Open the dust bag compartment lid
by turning the locking lever in the
direction of the arrow.
en
21