Inhaltszusammenfassung für Baumer DABx AD2T Series
Seite 1
Betriebsanleitung Brückenverstärker Instruction Manual Bridge Amplifier DABx AD2T-xx-xxxx Irrtum sowie Änderungen in Technik und Design Baumer Electric AG P.O. Box vorbehalten. Hummelstrasse 17 CH-8501 Frauenfeld This Manual is subjected to change without notice. http://www.baumer.com DABx_AD2T_BA_V1_0m.doc 1/20 Baumer Electric AG 01.04.09/rut...
Mounting ............................13 Function ............................13 Overview of the operating controls....................13 Electrical connection ........................14 RESET – Function..........................16 Error message via LED ........................18 Technical data ..........................19 Electrical data ..........................19 Mechanical data ..........................20 Environmental conditions .......................20 DABx_AD2T_BA_V1_0m.doc 2/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Stellen Sie sicher, dass das Personal die Betriebsanleitung und hier besonders das Kapitel „Sicherheits- und Betriebshinweise“ gelesen und verstanden hat. • Ergänzend zur Betriebsanleitung allgemeingültige gesetzliche und sonstige verbindliche Regelungen zur Unfallverhütung und zum Umweltschutz beachten und sicherstellen. DABx_AD2T_BA_V1_0m.doc 3/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Der Brückenverstärker kann an der Maschinenstruktur mit zwei M4 Schrauben befestigt werden. Anschluss der Stecker siehe Kapitel 4.2 Elektrische Anschlüsse. Funktion Übersicht der Bedienungselemente Schauglas für LED-Anzeige 4-Pol female (Serie 712) 5-Pol (Serie 713) manueller Reset-Knopf unter der Abdeckung DABx_AD2T_BA_V1_0m.doc 4/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
+/-6mV/V, kann der Verstärker nicht tariert werden und die rote LED leuchtet auf. Es bestehen zwei Möglichkeiten der Tarierung. 1. Über den Pin 5 kann der Verstärker via Steuerung tariert werden. 2. Unter der Verstärkerabdeckung befindet sich ein Reset-Knopf, der manuell betätigt werden kann. DABx_AD2T_BA_V1_0m.doc 7/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
1. Der Tarierbereich von +/-6mV/V ist überschritten und der Verstärker kann nicht tarieren. 2. Es liegt ein Kabelbruch vor oder das Kabel ist nicht richtig angeschlossen und es kann nicht tariert werden. DABx_AD2T_BA_V1_0m.doc 9/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
5-pol male (Serie 713) Anschluss Sensor 4-Pol female (Serie 712) Gehäuse Aluminium anodisiert Umgebungsbedingungen Betriebstemperaturbereich -25...+85° C Lagertemperaturbereich -40...+100° C Spez. Temperaturbereich 0…+70° C Schutzart IP 65 EN 61000-6-2 Immunität EN 61000-6-3 Emission DABx_AD2T_BA_V1_0m.doc 11/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Ensure that the personnel have read and understood the operating instructions, particularly the section "Safety and operating notes". • In addition to the operating instructions, generally applicable legal and other binding regulations for accident prevention and environmental protection must be reliably observed. DABx_AD2T_BA_V1_0m.doc 12/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
The bridge amplifier can be mounted with two M4 screws at the machine structure. For plug connection please see chapter 4.2 electrical connections. Function Overview of the operating controls Inspection glass for LED 4-Pol female (Serie 712) 5-Pol (Serie 713) Reset button underneath amplifier cover DABx_AD2T_BA_V1_0m.doc 13/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Sensor side Control side S/G bridge Signal Description PIN Signal Exc. + Full bridge + Vs Sig. - Full bridge - Vout Sig. + Full bridge Exc. - Full bridge + Vout Reset DABx_AD2T_BA_V1_0m.doc 14/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Seite 15
Sensor side Control side S/G bridge Signal Description PIN Signal Exc. + Full bridge + Vs Sig. - Full bridge n.c. (GND) Sig. + Full bridge Exc. - Full bridge + Iout Reset DABx_AD2T_BA_V1_0m.doc 15/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
6mV/V, it is not possible to tare the signal anymore and the LED will turn on. There are two possibilities to reset the amplifier. 1. Reset by the control via the connector pin 5. 2. Underneath the amplifier cover by pressing the reset button manually. DABx_AD2T_BA_V1_0m.doc 16/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
Seite 17
Reset time (< 5ms) Reset impulse (> 1ms) DABI AD2T: Output signal mV/V Input signal Reset Reset input (active high) Reset delay (< 0.3ms) Reset time (< 5ms) Reset impulse (> 1ms) DABx_AD2T_BA_V1_0m.doc 17/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
The following errors may occur: 1. The reset range of +/-6mV/V has exceeded and it is not possible to reset the amplifier. 2. The cable is broken or not connected properly, reset is not possible. DABx_AD2T_BA_V1_0m.doc 18/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
0250 < 15mVpp Noise 0.50 < 7.5mVpp 0350 < 12mVpp 1.00 < 5mVpp 0500 < 7.5mVpp 2.00 < 5mVpp 1000 < 5mVpp For further information please see the data sheet on www.baumer.com. DABx_AD2T_BA_V1_0m.doc 19/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...
4-Pol female (Series 712) Housing Anodized aluminum Environmental conditions Operating temperature range -25...+85° C Storage temperature -40...+100° C Specified temperature range 0…+70° C Protection class IP 65 EN 61000-6-2 Immunity EN 61000-6-3 Emission DABx_AD2T_BA_V1_0m.doc 20/20 Baumer Electric AG 01.04.09/rut Frauenfeld, Switzerland...