KYONE ULTIMA STAGGER TOOTH PRO Benutzerhandbuch Seite 6

ENGLISH
What you will find in the box:
• KYONE Clipper
• Charging base/docking station (on selected models!!)
• Adapter
• Attachment combs (1.5/3/4.5/6/10/13)
• Cleaning brush
• Oil bottle
• User Manual
Device operation.
Description.
1 Cutting head
2 Cutting head adjustment side lever
3 ON/OFF switch
4 Indicator light
(Blue/red is charging)
(Green/off is charged)
5 Attachment combs
(6 pieces: 1.5/3/4.5/6/10/13mm)
Using and charging the battery without a charging station.
The device contains a lithium battery. When the device is delivered, it is not yet fully charged. You
should therefore fully charge the battery before using it for the first time. Before charging, make sure
that the mains voltage corresponds to the voltage indicated on the device.
Connect the supplied adapter to mains power and then directly into the device. The battery only
reaches its full performance capacity after a few charging cycles.
While charging, a BLUE/RED indicator light will be lit. When the battery is fully charged, the light will
turn off/the light will be green.
Charging the battery while it is not yet (completely) empty does not affect the performance
of the device. However, we recommend that you allow the battery to be completely discharged from
time to time and
then fully charge it again to extend battery life.
➢ Arrange the power cord so that no one trips over it.
➢ Keep the cord, device and adapter away from hot surfaces.
Charging with a charging station. If included!
Check that the charging station is on a flat surface. Connect the supplied adapter to the charging
station. Then plug the adapter plug into a working power outlet. Place the switched off device in the
charging station.
Turning the device on and off.
The device is switched on or off with the on/off switch. (3)
Cutting length setting.
The cutting head can be adjusted to different lengths using the adjusting side lever (2).
0.5/1.5/2.5/3.5/4.0mm.
1_______
_______5_________
2______
3_______
4__________
10
Adjustment of the cutting length using attachment combs.
The attachment combs can be placed on the cutting head for different
cutting lengths. These are supplied with the device, in sizes
1.5/3/4.5/6/10/13mm. (5).
These are placed on the device with the help of a magnet in the attachment comb.
Cleaning and maintenance.
To maintain the optimum cutting performance of the appliance, you should regularly
maintain the device. The best thing is cleaning and oiling every day.
➢ Switch off the device and disconnect it from the mains.
Remove the comb attachment from the cutting head, if in use.
Remove all hair and other contaminants with the supplied brush.
Carefully remove the cutting head from the device. (If possible)
Oil the cutting head; if you use the device regularly, we recommend that you do this before each use.
Oil all the parts of the cutting head that contact each other.
Only use the special oil supplied with the device (do not dilute, it will not hinder the course of the
cutting head).
To clean the housing of the device, you can use a slightly damp (not wet) cloth. Do not use aggressive
or abrasive cleaning agents when cleaning the device.
If the cutting head takes less hair after a while, it can be replaced
with a new original one (available as a spare part from KYONE).
Cleaning the cutting head/Changing the side lever and/or making it infinitely adjustable
Step 1: Loosen both screws counter clockwise and take off the cutting blades. Leave the plastic part,
including spring, in place.
Step 2: Just unscrew the right screw. This is to block the nut, so that you can loosen the screw of the
side lever without it spinning.
Step 3: Remove the screw from the side lever by unscrewing it counter clockwise and put it next to
the device.
Step 4: If you want to remove the click system, to be able to work continuously, remove the part that
you see circled. Keep this safe!
Step 5: Replace the side lever and make sure to screw it back to the correct tension. Test this out by
moving the side lever up and down. This varies per person, but make sure it is not too tight or too
loose.
ENGLISH
11