Renkforce RF-CAP-600 Bedienungsanleitung Seite 6

• To edit 5 GHz WLAN, click on the tab "5G WiFi".
• Now you can change the name for the 5 or 5.8 GHz WLAN network and adjust the other
settings. Also here, you should create a new, secure password.
In principal, you could use the same name and the same password for both WLAN
networks. That way, you only need to connect your devices to one WLAN; the best
WLAN is always automatically used.
c) "Access-Point" configuration
• Start the setup by clicking the button "Wizard" on the left.
• In order to configure the product as Access Point click the orange "AP Mode" button.
• Here you first have to decide whether and how AP should obtain the IP address from the
router. Here we have 3 different options:
„Get IP From AC" - AP assigns the IP address and keeps the IP "192.168.188.253".
„Get IP From Gateway" - the DHCP server of the router assigns an IP address to AP. This
could also be used to configure AP. Check the device list of your router to find the IP address.
"Static IP" - You can assign a fixed IP address to the AP, preferably in the network area of
your router. You can always use this IP address to access the AP configuration.
We recommend that you let the router assign the address or you could assign a
static IP in the area of your router. That way you are always able to access the web
interface from within your network.
• Click "Next".
• Now configure the two WLAN networks, if not done already. See the sub-chapter "Configura-
tion of the WLAN Networks". Confirm each time with the button "Save".
• AP restarts and applies the settings.
If you configured via WLAN, you possibly need to reconnect your device to WLAN.
If you have changed the IP address or have the router assign one, then the AP will
be available under the new address only. You should also set the IP configuration in
the network settings of your device to auto.
d) "Router" configuration
• Start the setup by clicking the button "Wizard" on the left.
• In order to configure the product as Access Point click the orange "Gateway Mode" button.
• First you have to select the type of internet access. If you are using a DSL modem, select
"PPPoE" and enter the necessary login details. If you want AP to run behind a cable modem,
where no dial-in data is needed, select "DHCP.
• Click "Next".
• Now configure the two WLAN networks, if not done already. See the sub-chapter "Configura-
tion of the WLAN Networks". Confirm each time with the button "Save".
• AP restarts and applies the settings.
If you configured via WLAN, you possibly need to reconnect your device to WLAN.
If you have changed the IP address or have the router assign one, then the AP will
be available under the new address only. You should also set the IP configuration in
the network settings of your device to auto.
Resetting to Factory Settings
In order to reset the product to the factory settings, it should be connected and active. To do
this, proceed as follows.
a) At the product
• Press and hold the "RST" button (H) on the product for more than 5 seconds.
• Then release the button. The status LED (A) is red and flashing fast.
• The product will restart with the factory settings. This process will last about 1 to 2 minutes.
Once the status LED (A) is lit and white, the process is complete.
b) In the web interface
• Open the product's web interface and log in.
• Open the item "Manage".
• In the tab "Configure" select "Reset Default" and click on "Reset Default" at the bottom to
reset.
• The product will restart with the factory settings. This process will last about 1 to 2 minutes.
Once the status LED is lit blue, the process is complete.
Care and Cleaning
• Disconnect the product from the power supply before cleaning.
• Use a dry, lint-free cloth to clean the product.
• Never use abrasive cleaning agents, rubbing alcohol or other chemical solutions, since these
could damage the casing or even impair operation.
Declaration of Conformity (DOC)
We, Conrad Electronic SE, Klaus-Conrad-Straße 1, D-92240 Hirschau, hereby declare that this
product conforms to the 2014/53/EU directive.
The full text of the EU conformity declaration is available at the following Internet
address:
www.conrad.com/downloads
Select a language from the menu and enter the order number of the product in the
search field; Now you can download the EU declaration of conformity in PDF format.
Disposal
Electronic devices are recyclable materials and do not belong in the household was-
te. Dispose of an unserviceable product in accordance with the relevant statutory
regulations.
Technical Data
a) Product
Operating voltage ......................... 48 V/DC (PoE); 12 V/DC (DC IN)
Power demand ............................. max. 0.5 A (PoE); 1.5 A (DC IN)
Ports ............................................. 2x RJ45 10/100/1000 MBit/s, 1x WAN/PoE, 1x LAN
WLAN ........................................... IEEE802.11b/g/n/ac/ax; WiFi 6; 2.4 GHz (max. 600 MBit);
5 GHz, 5.8 GHz (max. 1200 MBit) Dual Band 2*2 MIMO
Frequency range/transmit power ... 2.412 – 2.472 GHz, ≤ 20 dBm;
5.180 – 5.240 GHz, ≤ 23 dBm
5.745 – 5.825 GHz, ≤ 13.98 dBm
Supported protocols ..................... IEEE802.3at (48 V PoE); IEEE802.3az
Encryption protocols ..................... WPA/WPA2
Operating modes .......................... Access Point; router
Chip set ........................................ Qualcomm IP6000
Memory ......................................... SPI-NOR 8 MB, NAND 128 MB
Supported features ....................... MU-MIMO; DL/UL-OFDMA; Wave2.0; OFDMA; 1024-QAM;
Seamless roaming; QSDK driver
Dimensions (W x H x D) ............... approx. 198 x 38 x 198 mm
Weight .......................................... approx. 720 g (AP only);
...................................................... including ceiling bracket approx. 790 g
Operating conditions ..................... 0 to +40 °C / 10 to 90% rel. air humidity (non-condensing)
Storage conditions ........................ -10 to +60 °C / 10 to 90% rel. air humidity (non-condensing)
b) PoE power supply
Operating voltage ......................... 100 - 240 V/AC, 50/60 Hz
Power consumption ...................... max. 0.8 A
Output ........................................... 48 V/DC, 500 mA, 24 W
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
© Copyright 2021 by Conrad Electronic SE. 2362173_V1_0721_02_m_RR_VTP_4L