En Original Instructions; Declaration Of Conformity; Specified Use; General Safety Instructions - Metabo STEB 65 Quick Originalbetriebsanleitung

Original Instructions

1. Declaration of Conformity

We, being solely responsible: Hereby declare that
these jigsaws, identified by type and serial number
*1), meet all relevant requirements of directives *2)
and standards *3). Technical documents for *4) -
see page 3.

2. Specified Use

The machine is suitable for sawing non-ferrous
metals and sheet steel, wood and similar materials,
plastics and similar materials. Any other use is not
permitted.
The user bears sole responsibility for any damage
caused by inappropriate use.
Generally accepted accident prevention
regulations and the enclosed safety information
must be observed.

3. General Safety Instructions

For your own protection and for the
protection of your power tool, pay
attention to all parts of the text that are
marked with this symbol!
WARNING – Reading the operating
instructions will reduce the risk of injury.
WARNING Read all safety warnings and
instructions. Failure to follow all safety
warnings and instructions may result in electric
shock, fire and/or serious injury.
Keep all safety instructions and information for
future reference.
Pass on your power tool only together with these
documents.

4. Special Safety Instructions

Hold power tool by insulated gripping
surfaces, when performing an operation where
the cutting accessory may contact hidden
wiring. A cutting accessory contacting a "live" wire
may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
Ensure that the place where you wish to work is free
of power cables, gas lines or water pipes (e.g.
check using a metal detector).
During work, the workpiece must lay flat and be
secured against moving, e.g. using clamps.
Do not try to saw extremely small workpieces.
When sawing, the footplate must make secure
contact with the workpiece.
When interrupting a cut for any reason, release the
trigger and hold the saw motionless in the material
until the saw blade comes to a complete stop. Never
attempt to remove the saw from the workpiece while
the saw blade is in motion or kickback may occur.
Do not switch the machine on while the saw blade is
touching the workpiece. Let the saw blade reach full
speed before making a cut.
When restarting a saw in the workpiece, centre the
saw blade in the kerf and check that saw teeth are
not engaged into the material. If the saw blade
seizes, it may kickback from the workpiece when
the saw is restarted.
Keep hands well away from the sawing area and the
saw blade. Do not reach underneath the workpiece.
Remove chips and similar material only with the
machine at a standstill.
Pull the plug out of the socket before making any
adjustments, converting or servicing the machine.
Danger of injury due to the sharp jigsaw blade. After
stopping work, the jigsaw blade may still be hot.
Wear protective gloves.
Reducing dust exposure:
Some of the particles generated using this
power tool may contain substances known to
cause cancer, allergic reactions, respiratory
diseases, birth defects or other reproductive harm.
Some of these substances include: Lead (in paint
containing lead), mineral dust (from bricks,
concrete etc.), additives used for wood treatment
(chromate, wood preservatives), some wood types
(such as oak or beech dust), metals, asbestos.
The risk from exposure to such substances will
depend on how long the user or nearby persons are
being exposed.
Do not let particles enter the body.
Do the following to reduce exposure to these
substances: Ensure good ventilation of the
workplace and wear appropriate protective
equipment, such as respirators able to filter
microscopically small particles.
Observe the relevant guidelines for your material,
staff, application and place of application (e.g.
occupational health and safety regulations,
disposal).
Collect the generated particles at the source, avoid
deposits in the surrounding area.
Use only suitable accessories. In this way, fewer
particles enter the environment in an uncontrolled
manner.
Use a suitable extraction unit.
Reduce dust exposure with the following measures:
- Do not direct the escaping particles and the
exhaust air stream at yourself or nearby persons
or on dust deposits.
- Use an extraction unit and/or air purifiers.
- Ensure good ventilation of the workplace and
keep it clean using a vacuum cleaner. Sweeping
or blowing stirs up dust.
- Vacuum or wash protective clothing. Do not blow,
beat or brush.
5. Overview
See page 2.
ENGLISH en
9