Ferplast microchip pet flap Handbuch Seite 5

the body in any other way, seek medical advice immediately.
• Remove the batteries from the product when they are flat or if you do
not plan to use the product for an extended length of time. This
prevents damage due to leakage. If a battery has leaked, avoid contact
with skin, eyes and mucous membranes. If necessary, rinse the
affected areas with clear water and consult a doctor immediately.
Wooden doors (Fig.3)
A Measure the belly height of your cat from the floor and position the template (side A) on the door
with the bottom at the same height. Mark around the perimeter of the TEMPLATE on the door using
the marker.
B Drill 4 holes in the corners of the marked area.
C Cut along the perimeter using the jig saw to join the 4 holes.
D Smooth the edges using a file or sandpaper.
The biggest job is done. Go to paragraph "Fit the flap".
Glass doors (Fig.4)
WARNING! Cutting glass can be dangerous. You must consult a glass merchant before starting the job.
It is impossible to drill holes in toughened safety glass or double-glazing unless they have already been
drilled when the panes are manufactured.
A Measure the belly height of your cat from the floor and position the template (side A) on the door
with the bottom at the same height.
B Mark the bottom side using a marker, you will use it as the base to center the compasses on the
points marked on the template. Then drill a circular hole with radius of 108 mm. (The centre of the
hole is marked on the template).
The biggest job is done. Go to paragraph "Fit the flap".
Metal doors
Follow the same instructions as those for wooden doors. The only difference lies in the fact that the
electronic system does not work near metallic objects. It is to be insulated using a non-metal material
(wood or similar), which must have a minimum thickness of 50 mm around the entire perimeter. This
prevents any interference and ensures the correct operational efficiency of the magnetic mechanism.
The biggest job is done. Go to paragraph "Fit the flap".
Walls
Follow the same instructions as those for wooden doors. (Steps B-C-D are to be done using suitable
tools). The tunnel supplied can be installed in walls with a thickness of no more than 55 mm. If the wall
is thicker than this, the tunnel must be extended in cement plastering or by purchasing the special
plastic extension (Tunnel Extension) available as an accessory for the Swing flaps range.
The biggest job is done. Go to paragraph "Fit the flap".
FIT THE FLAP (Fig. 5)
Position the flap on the hole and using a marker, mark the positions where the screws are required.
Remove the flap and drill 4 holes using a drill with a 4.5 mm bit. (The 4-way locking system is to be fitted
on the inner side of the door). Fit the flap and secure it with the screws supplied, which may have to be
cut and filed to remove any sharp edges. 4 short screws are supplied for fitting to glass doors and fly
screens and 4 long screws for all other installations on a thickness of up to 55 mm. The 4 long screws
will have to be shortened for installations on an intermediary thickness (i.e.: for installations on a
thickness of 45 mm shorten the screws by 10 mm; for installations on a thickness of 35 mm shorten the
screws by 20 mm, and so on). Instead, you could purchase a new set of screws to your specifications at
your local hardware store. Too short a screw could strip the thread whereas too long a screw could
break the front panel of the pet door. To finish the job, cover the screw holes using the plugs supplied,
making sure to match the rib to the seat.
INSERT THE BATTERIES (Fig. 6)
When the flap is fitted you can insert the batteries in their compartment; the flap requires
6x1.5 AA LR6 batteries. We recommend using only good quality alkaline batteries, in order to ensure
the product works properly. Insert the batteries correctly and wait for 10 seconds. If any microchip has
not been previously recorded the LED will start flashing with cycles of 3 consecutive flashes.
Low batteries warning:
The LED will flash every 5 seconds to indicate that the batteries need replacing.
YOUR SWING MICROCHIP FLAP IS NOW READY TO USE!
MICROCHIP RECORDING (Fig.7) To record your cat microchip press the memory button once, bring
your cat to the flap and the code will automatically be recorded (you'll hear the door unlocking). Since
then, every time your cat comes near the flap the device will identify him, allowing him to go through
it. The recording time lasts 10 seconds maximum. To record more microchips, following the instructions
in the same order.
MEMORY DELETING If you need to delete the product memory, it is sufficient to press the memory
button for 10 seconds and it will be reset (the LED will activate with cycles of 3 consecutive flashes).
MANUAL MODE If you do not wish to use the electronic system, the cat flap can be converted to work
manually. To do so, press the memory button twice and the electronic system will be switched off. By
pressing the button again (just once) the product will reactivate the electronic functions keeping the
previously recorded microchips.
CLEANING: QUICK AND EASY (Fig.8)
The product does not require any special maintenance, just an ordinary cleaning of the flap (A) and of
the infrared detectors placed inside the tunnel (B), at the left and right side, by using a soft and dry
cloth.
IMPORTANT
Within the European Community the crossed-out rubbish container on wheels symbol on the product,
the safety information or the packaging indicates that the product must not be treated as general
household waste, in accordance with the guideline valid in the European Community (2012/19/EC) and
the regulations at its place of use. The product must be disposed of by a waste separation business or
at an authorised collection point for recycling old electrical and electronic appliances, in compliance
with the statutory regulations of the country in which the product is used. Improper handling of waste
products of this kind can have negative effects on the environment and personal health due to the
potentially dangerous materials often contained in old electrical and electronic appliances. By
disposing of these products properly you also contribute to an effective use of natural resources. You
can obtain more information from distributors of the product, the relevant public offices, and the
national organisations of the manufacturer.
GB
D
FR
HU
SK
CS
PL
TR