Gleich- Und Wechselstrommessung; Data Hold; Relativwertmessung; Manueller/Automtischer Messbereich - UNI-T UTD1025CL Bedienungsanleitung

UTD1000L User Manual

Relativwertmessung

Manual
To power on off the Oscilloscope
:
Diese Funktion dient zur Ermittlung von Relativwerten bei der Kondensatormessung. Dabei wird der momentane Messwert
F1 F4 To set up the submenus
～ :
auf 0 gesetzt und gespeichert. Es lassen sich somit bequem Messwertänderungen ablesen.
To toggle between Scope (DSO) and
:
er on off the Oscilloscope Press this button under DSO mode to
/ • Drücken sie die Taste : und anschließend so lange die F1 Taste, bis Cap angezeigt wird.
multimeter (DMM) modes
access MEASURE auto measurement
up the submenus
• Drücken Sie die F2 Taste ( REL ). Es erscheint ein Δ-Symbol auf dem Display.
Press this button to access ACQUIRE
:
menu or press SHIFT first and then the
e between Scope (DSO) and
• Nun können Sie eine Messung an einem Kondensator durchführen.
(sample mode)menu if under DSO mode
button to access COURSOR cursor
ter (DMM) modes
.
press SHIFT first and then this button to
Durch erneutes Drücken der F2 Taste wird der Relativwert wieder gelöscht. measurement)menu if under DMM
s button to access ACQUIRE
access intensity, with help of right and left
mode press the button to access
mode)menu if under DSO mode
;
arrow buttons, you can change screen
resistance measurement menu and

Gleich- und Wechselstrommessung

IFT first and then this button to
brightness. If under DMM mode pressing
measure resistance diode continuity/
tensity, with help of right and left
Messungen bis 400 mA:
this button can access voltage capacitance
tons, you can change screen
• Stecken Sie die schwarze Messleitung in die COM-Buchse ② und die rote Messleitung in die µAmA-Buchse ③.
: In DSO mode press it to access measurement menu
UTD1000L User Manual
s. If under DMM mode pressing
,
CHANNEL menu for UTD1000CL
• Drücken Sie auf die Taste, um die Strommessung aufzurufen.
: Press this button to access DISPLAY
n can access voltage
repeatedly press to toggle between two
• Mit der F1 Taste können Sie zwischen Gleichstrom ( A DC ) und Wechselstrom ( A AC ) wechseln. (Display mode) menu if under DSO mode
ment menu
. channel menus for UTD1000DL
• Mit der F3 Taste können Sie den Messbereich festlegen (µA und mA, nicht A!). or press SHIFT first and then this button to
To power on off the Oscilloscope
:
button to access DISPLAY In DSO mode, press the button to access
:
access CONFIGURE
• Legen Sie die Messspitzen in Reihe zum Messobjekt an.
F1 F4 To set up the submenus
～ :
FFT menu for UTD1000CL or press the
mode) menu if under DSO mode
;
configuration menu pressing this button
To toggle between Scope (DSO) and
: button and then F1 button to toggle between
SHIFT first and then this button to
Vorsicht: Messen Sie keine Ströme über 400 mA ohne Adpater!
under DMM mode to access current
! FFT and MATH menus for UTD1000DL multimeter (DMM) modes
ONFIGURE interface
(
Legen Sie die Messspitzen niemals parallel zum Messobjekt an!
measurement menu
Press SHIFT first and then the button to Press this button to access ACQUIRE
:
tion menu pressing this button
) ;
Beachten Sie die Maximal zulässige Spannung von 400 V!
access STATUS display
(sample mode)menu if under DSO mode
MM mode to access current
press SHIFT first and then this button to
ment menu
.
Messungen bis 10 A:
access intensity, with help of right and left
• Stecken Sie den Messadapter UT-M07 in die Messbuchsen COM ② und µAmA ③, sodass die Schrift des Adpaters
arrow buttons, you can change screen
Measuring DC Current with UTD1000CL
hinten steht.
brightness. If under DMM mode pressing
• Stecken Sie die schwarze Messleitung in die schwarze Messbuchse und die rote Messleitung in die rote Messbuchse
To measure DC current lower than 4mA do the
he following this button can access voltage
:
des Messadapters.
measurement menu
following
asurement type to DC
• Drücken Sie auf die Taste, um die Strommessung aufzurufen.
: Press this button to access DISPLAY
1. Press I button to set measurement type to DC
• Mit der F1 Taste können Sie zwischen Gleichstrom ( A DC ) und Wechselstrom ( A AC ) wechseln. (Display mode) menu if under DSO mode
Current
• Drücken Sie die F3 Taste so lange, bis der Messbereich A eingestellt ist und bestätigen Sie mit der OK Taste➋. or press SHIFT first and then this button to
AC Voltage option.
access CONFIGURE
• Legen Sie die Messspitzen in Reihe zum Messobjekt an.
F3 to toggle between
s into multimeter
configuration menu pressing this button
the default is mA
under DMM mode to access current
Vorsicht: Messen Sie keine Ströme über 10 A!
COM and Red to V/Ω
).
!
measurement menu
2. Plug test lead connectors into input terminals
Legen Sie die Messspitzten niemals parallel zum Messobjekt an!
ctively to tested
Beachten Sie die Maximal zulässige Spannung von 400 V!
(Black to COM and Red to
ge reading.
3 Connect test leads to tested points then
.
take DC current reading
g AC Voltage
Figure 5-7 Measuring DC Current lower than 4mA
20
BP830486.indd 20-21
Press this button under DSO mode to
/ :
access MEASURE auto measurement
menu or press SHIFT first and then the
button to access COURSOR cursor
.
( ) measurement)menu if under DMM
; mode press the button to access
;
( resistance measurement menu and
; measure resistance diode continuity/
, capacitance
: In DSO mode press it to access
,
/ / CHANNEL menu for UTD1000CL
. repeatedly press to toggle between two
, . channel menus for UTD1000DL
;
In DSO mode, press the button to access
:
FFT menu for UTD1000CL or press the
;
button and then F1 button to toggle between
Press this button under DSO mode to
/ :
FFT and MATH menus for UTD1000DL
interface
(
access MEASURE auto measurement
;
Press SHIFT first and then the button to
Figure 5-22 Measuring Capacitanc in Relative
) ;
menu or press SHIFT first and then the
access STATUS display
button to access COURSOR cursor
Mode
. .
. measurement)menu if under DMM
mode press the button to access
.
;
resistance measurement menu and
measure resistance diode continuity/
Selecting Manual Auto Ranging
capacitance
9
: In DSO mode press it to access
The multimeter defaults at auto mode. To access
,
CHANNEL menu for UTD1000CL
,
repeatedly press to toggle between two
manual ranging, operate as follows:
. channel menus for UTD1000DL
:
1. Press V or R button, and measure mode
In DSO mode, press the button to access
:
FFT menu for UTD1000CL or press the
;
option is AUTO
button and then F1 button to toggle between
measurement unit is μA you can use
, ,
FFT and MATH menus for UTD1000DL
2 Press F2 to select manual measure mode
interface
( .
μA mA and A ranges
,
Press SHIFT first and then the button to
) ;
then the ranging mode will change into Manual
access STATUS display
.
5 2
μA mA
/ )
,
.

Data Hold

Mit dieser Funktion halten Sie den momentanen Messwert fest.
( )
• Drücken Sie die
;
• Am Display erscheint ein blinkendes "Hold".
(
;
Durch erneutes Drücken der
,
Manueller/Automatischer Messbereich
/ /
UTD1000L User Manual
Der automatische Messbereich ist standardmäßig aktiviert.
.
,
Um den Messbereich manuell festzulegen, gehen Sie wie folgt vor:
;
To power on off the Oscilloscope
• Drücken Sie die :
F1 F4 To set up the submenus
• Drücken Sie die F2 Taste und stellen Sie Range Mode auf Manual . ～ :
To toggle between Scope (DSO) and
:
• Mit der F3 Taste ( Range Select ) können Sie den Messbereich ändern.
multimeter (DMM) modes
;
• Der Messbereich wird am Display angezeigt.
Press this button to access ACQUIRE
:
• Durch erneutes Drücken der F2 Taste stellen sie wieder auf den automatischen Messbereich um.
(sample mode)menu if under DSO mode
.
( )
press SHIFT first and then this button to
;
.
access intensity, with help of right and left
(
arrow buttons, you can change screen
;
brightness. If under DMM mode pressing
,
this button can access voltage
9
measurement menu
/ /
/ : Press this button to access DISPLAY
.
(Display mode) menu if under DSO mode
,
;
or press SHIFT first and then this button to
access CONFIGURE
configuration menu pressing this button
under DMM mode to access current
;
measurement menu
.
.
,
,
.
9
3 9
Under DSO mode, press to set up
:
REF waveform recall) menu.
(
SINGLE single trigger function press
( ) ;
Under DSO mode, press to automatically
:
first SHIFT and then the button to access
set up the waveform press SHIFT first
;
REF waveform recall) menu.
(
and then the button to switch on full
Under DSO mode, press to automatically
:
autoset function The Oscilloscope can
.
set up the waveform press SHIFT first
;
automatically adjust the ranges to obtain
UTD1000L User Manual
and then the button to switch on full
optimal waveform based on the input
autoset function The Oscilloscope can
.
signal without any manual interference
.
automatically adjust the ranges to obtain
Taste, um den Data Hold zu aktivieren.
: Under DSO mode, press to start/stop data
RUN/STOP
optimal waveform based on the input
UTD1000L User Manual acquisition if under DMM press the
; ,
status accordingly
.
signal without any manual interference
button to lock measuring readings on
Taste kehrt das Gerät zur normalen Messung zurück.
: Under DSO mode, press to start/stop data
RUN/STOP 3.Under manual ranging mode, keep pressing F3
the screen
.
acquisition if under DMM press the
; ,
:
Under DSO mode, press to access To power on off the Oscilloscope
: /
button to reach up to the highest range
button to lock measuring readings on
1 0
F1 F4 To set up the submenus
～ :
the screen
.
after that, then the selected range jumps directly
To toggle between Scope (DSO) and
:
: Under DSO mode, press to access
multimeter (DMM) modes
.
to the lowest range and circulates again.
1 0
Press this button to access ACQUIRE
:
/ Taste für Spannungsmessung oder die Taste für Widerstandsmessung. :
The currently selected range shows just above
(sample mode)menu if under DSO mode
press SHIFT first and then this button to
measuring readings.
access intensity, with help of right and left
.
4 Press F2 button, Auto icon shows on left upper
.
arrow buttons, you can change screen
brightness. If under DMM mode pressing
,
;
display indicating the multimeter has
,
this button can access voltage
returned to full autoset mode
measurement menu
.
: Press this button to access DISPLAY
: In DSO mode press it to access
(Display mode) menu if under DSO mode
, ;
CHANNEL menu for UTD1000CL
or press SHIFT first and then this button to
repeatedly press to toggle between two
access CONFIGURE interface
. ( channel menus for UTD1000DL
configuration menu pressing this button
) ; :
FFT menu for UTD1000CL or press the
under DMM mode to access current
;
button and then F1 button to toggle between
measurement menu
.
FFT and MATH menus for UTD1000DL
interface
(
Press SHIFT first and then the button to
) ;
access STATUS display
.
Figure 5-23 Manual Ranging
function options
information
.
Timebase: To change scan rate, ranging
:
Combine with other buttons to select
SHIFT ::
from 50s/div 10ns/div for 25MHz
ns ～ -
function options
bandwidth models and 50s/div 5ns/div
～
Timebase: To change scan rate, ranging
:
for 50MHz bandwidth models and
-
from 50s/div 10ns/div for 25MHz
ns ～
stepping in 1-2-5 Press s to access
. " "
bandwidth models and 50s/div 5ns/div
～
relatively slower scan rate or ns to
" "
for 50MHz bandwidth models and
-
speed up
.
stepping in 1-2-5 Press s to access
. " "
: Vertical Scale: To change vertical scaling,
relatively slower scan rate or ns
"
ranging from 5mV/div 20V/div and
～
speed up
.
.
stepping in 1-2-5 Press V to zoom
. " "
:
Vertical Scale: To change vertical scaling,
in current vertical scale or mV to
" "
ranging from 5mV/div 20V/div and
～
zoom out
Press this button under DSO mode to .
:
, stepping in 1-2-5 Press V
. " "
access MEASURE auto measurement
(
in current vertical scale or mV
"
menu or press SHIFT first and then the
;
zoom out
.
button to access COURSOR cursor
(
measurement)menu if under DMM
;
Press this button under DSO mode to
mode press the button to access
,
access MEASURE auto measurement
; ( )
resistance measurement menu and
menu or press SHIFT first and then the
;
measure resistance diode continuity/
/ /
button to access COURSOR cursor
(
capacitance
.
measurement)menu if under DMM
;
: In DSO mode press it to access
,
mode press the button to access
,
CHANNEL menu for UTD1000CL
;
resistance measurement menu and
repeatedly press to toggle between two
measure resistance diode continuity/
/ /
.
channel menus for UTD1000DL
capacitance
.
In DSO mode, press the button to access
:
,
FFT menu for UTD1000CL or press the
;
;
button and then F1 button to toggle between
FFT and MATH menus for UTD1000DL
Press SHIFT first and then the button to
In DSO mode, press the button to access
access STATUS display
.
;
.
.
9
21
15.12.15 16:17
-
to
"
to zoom
)
to
"
.