HPI Racing FLUX RELOAD F Kurzanleitung

FLUX F
FLUX 2 IN I PROFESSIONAL BOX
Program Box Connection 70n
To enable your program box to work you must first disconnect
need to plug the receiver cable in to the slot in the program
pack and the program box will be operational. You must
will show "Connecting ESC" and then will show you the mode
0 Y V—&FluxÄ
FLUX REI.OMI
USE s.sv
Program Card Operation Y ü L
There are 4 buttons on the program box: ITEM (Return), VALUE, MODE and 0K.
Y RIC It"1TEM" "VALUE" "MODE"
Used for main navigation
RETURN
Each time this button is pressed it will move to the next available range of settings.
Used for changing the values of a particular
li\l.lJE
Used to enter the current mode of the speed control. Changes are made with the value button.
Used for confirming new settings.
Once 0K is pressed "Save Data 0K" will be displayed
Programmable Mode Settings
Programmable Modes Table Y ü
Programmable Mode Settings
2
Running Mode Fwd w/ Brake Fwd/REV/Brake Rock
Drag Brake Force
0% 5%
Auto-Lipo Cut off No Protection 2.6V/cell 2.8V/cell
2_6V/0'b
Start Mode (Punch)
Ll (Soft v 7 1')
Max Brake Force
25%
70 7 —
Max Reverse Force
25%
Initial Brake Force = Drag Brake
Neutral Range 6% (Narrow) 9% (Normal)
Motor Timing
0.000 3.750
Over Heat Protection
Enable Disable
-jD5-,9bON -ytJi5FOFF
#101280 FLUX RELOAD 2-1N.1 PROFESSIONAL PROGRAM BOX
Y a Y
the Flux receiver cable from the receiver as shown.
box marked with Connect the Flux power wires to a suitable
then press a button for the program box to connect to the ESC. The program
that the speed control is set to.
C. L "Connecting ESC"
White wire
Red wire
LJ•y
ESC
Black wire
D
through the program functions.
setting.
to confirm value is accepted.
"Save Data 0K"
Y ü Y y y
3 4 5 6 7
Crawler
10% 20% 40% 60% 100%
3.OV/ce11 3.2V/ce11 3.4V/ce11
3.4V/-t'/b
L3 16 L8
75% 100%
75% 100%
(Wide)
7MF
7.500 11.250 15.000 18.750 22.500 26.250
Programmable Values
hpi•racing
WWW - EUROPE corn
The programmable values shown on page 1 each have a different effect on how the Flux Reload ESC operates. Below is an explanation
Program Modes
UNNING MODE
Once unplugged you
FWD w/Brake - This mode offers forward
battery
FWD/REV/Brake - This mode offers Forw•ard, Brake and Reverse. Note, The Reverse function
box
be activated once the motor has stopped moving
Rock Crawler - This mode is used for Rock Crawlers. It will allow instant switching
if the Rock Crawler mode is used. This mode is not recommended
- iifjjC
- üijL
DRAG BRAKEFORCE Füy
This mode allows the setting of an automatic drag brake when the throttle stick is retumed to neutral, simulating the slight braking effect of a brushed motor while coasting.
IA
UTO LIPO CUTOFF
As shown on page 4 the auto-Lipo
select the suitable cell voltage for the low voltage protection
WARNING: Never use the default value " No Protection"
The Flux Reload ESC will monitor
reduced by 50%. This will allow enough time to bring the car back to you. After 10 seconds
Flux e—
TART MODE (PUNCH)
This mode selects the level of "punch"
packs with low discharge rates or are poor quality will not be able to supply the needed power. It can also cause the motor to not run smoothly or tremble.
AXIMUM BRAKE FORCE
The Flux Reload ESC provides a proportional brake function. This mode sets the brakes force applied when the throttle is at full brake. A very large brake force may
slow the car quickly but be aware it can also do damage to the car's drivetrain.
MAXIMUM REVERSE FORCE
This mode will set the reverse power applied by the Flux Reload ESC. The higher the value the quicker the reverse function will be.
NITIAL BRAKE FORCE
This setting refers to the very first part of the braking zone. As default this is set to equal the Drag Brake Force which will give a smooth transition into braking.
It can also be set higher to allow for a more aggressive braking function initially.
NEUTRAL RANGE
8 9
The neutral range is the area around
TIMING
L9 (Aggressive)
Different types of Brushless motors will react differently to timing values. Generally the higher the timing setting the more output power and performance you will gain.
This is however balanced off with less run time, heat build up and efficiency of the system. We recommend the default timing as a good balance of performance and
run time.
OVER HEATPROTECTION
If the function is activated, the output power will be cut off when the temperature of the Flux Reload ESC is up to the factory threshold for more than 5 seconds.
When the protection happens,
y ü
1-2
and Brake only.
uses a soft start "Double click" function
forward.
from forward to reverse for quick car control. Please set the Drag Brake Force to 100%
for use with non rock crawling cars.
cut off value is changed depending on the type of battery you will be using in your RC car. When using a Lithium
of your battery pack.
if you are using a Lithium battery!
the battery output voltage. If the voltage drops lower than the preset threshold
the Flux Reload ESC will cut output power completely.
V
F:
from a standing start. Level 1 is soft right up to level 9 which is very aggressive.
fikU— <
-Y
* —X:
* —X:
the centre of the throttle movement. This mode will increase or decrease
e— 1-2 3 Y
b:
the green LED will flash.
2
of each program mode.
which will only allow reverse to
based pack please
for more than 2 seconds, the output power will be
Please note, if levels 7-9 are selected, battery
this area to suit your individual preference.