Before The First Use - Rondell Rde-1051 Betriebsanweisung

ENGLISH
•
Do not wash the thermopot in a dishwashing machine.
•
Before taking the unit away for long storage or before cleaning,
unplug it, pour out water and let the unit cool down and dry.
•
For children's safety reasons do not leave polyethylene bags
used as packaging unattended.
Attention! Do not allow children to play with polyethylene bags or
packaging film. Danger of suffocation!
•
Close supervision is necessary when children or disabled per-
sons are near the operating unit.
•
This unit is not intended for usage by children.
•
Place the unit out of reach of children during the operation
and cooling down.
•
Do not allow children to touch the unit body and the power cord
during the unit operation.
•
The unit is not intended to be used by people with physical,
sensory or mental disabilities (including children) or by per-
sons lacking experience or knowledge if they are not under
supervision of a person who is responsible for their safety or if
they are not instructed by this person on the usage of the unit.
•
Do not leave children unattended to avoid them using the
unit as a toy.
•
Check the integrity of the power cord, the power plug and the
thermopot body periodically.
•
Never use the unit if the power cord or the power cord plug is
damaged, if the unit works improperly or after it was dropped.
•
If the power cord is damaged, it should be replaced by the
manufacturer, a maintenance service or similar qualified per-
sonnel to avoid danger.
•
Do not repair the unit by yourself. Do not disassemble the
unit by yourself, if any malfunction is detected or after it was
dropped, unplug the unit and apply to any authorized service
center from the contact address list given in the warranty cer-
tificate and on the website www.ron dell.ru.
•
Transport the unit in the original packaging only.
•
Keep the unit out of reach of children and people with disabilities.
THIS UNIT IS INTENDED FOR HOUSEHOLD USE ONLY. ITS
COMMERCIAL USAGE AND USAGE IN PRODUCTION AREAS
AND WORK SPACES IS PROHIBITED.

BEFORE THE FIRST USE

After the unit transportation or storage at low temperature
keep it for at least three hours at room temperature before
switching on.
There may be water spots in the thermopot, this is normal, as the
unit has undergone factory quality control.
•
Unpack the thermopot; remove any advertising stickers that
can prevent the unit operation.
•
Check the unit for damages, do not use it in case of damages.
•
Make sure that the unit operating voltage corresponds to the
voltage of your mains.
•
Place the thermopot on a dry flat surface keeping at least
20 cm gap between the thermopot body and the wall or furni-
ture and at least 50 cm gap above the thermopot.
•
Open the lid (8) by pressing the button (6) and holding it.
•
Fill the thermopot with water using a suitable bowl, do not
exceed the maximal water level mark «FULL».
•
Install the drip tray (1).
•
Insert the power cord (11) jack into the socket (10) on the ther-
mopot body, and the power cord (11) plug into the socket, all
indicators on the display (3) will light up for a few seconds, and
the touch buttons (12-16) illumination on the control panel (5)
will light up permanently. After that, the boiling process will
begin, while the display (3) will show the water temperature
(17) and the indicator (19) will flash.
•
After the boiling process is finished, the thermopot will auto-
matically switch to the keep warm mode, and the keep warm
mode indicator (22) will appear on the display (3), and the indi-
cator (19) will glow constantly.
•
Place a suitable bowl on the tray (1) and drain the water. To do
this, press the button (15), the corresponding indicator (23)
will light up on the display. After that press and hold the water
supply button (16).
Note: If, after unlocking, no action is taken for about 10 seconds,
the lock will be switched on again automatically and the corre-
sponding indicator (23) will go out.
Attention! Be careful when pouring out water to avoid burns
by hot water.
•
To switch the thermopot off, press and hold the button (13) for
more than 3 seconds and then release it.
•
To switch the thermopot off disconnect the power cord (11)
plug from the mains socket.
•
Open the thermopot lid (8) and wait until it cools down completely.
•
Carefully tilt the thermopot to drain the remaining water.
•
The thermopot is ready for operation.
USING THE THERMOPOT
•
Open the lid (8) by pressing the button (6) and holding it.
•
Fill the thermopot with water using a suitable bowl, do not
exceed the maximal water level mark «FULL».
•
Install the drip tray (1).
•
Insert the power cord (11) jack into the socket (10) on the ther-
mopot body, and the power cord (11) plug into the socket, all
indicators on the display (3) will light up for a few seconds, and
the touch buttons (12-16) illumination on the control panel (5)
will light up permanently. After that, the boiling process will
begin, while the display (3) will show the water temperature
(17) and the indicator (19) will flash.
10