Charging The Product; Technical Data; Power Supply; Cleaning And Care - Renkforce Rf-Efs-100 Bedienungsanleitung

7 Operation

7.1 Charging the product

Before first use, charge the product for 2-4 hours.
1. Make sure the product is switched off before charging.
2. Connect the USB-C plug of the charging cable to the USB-C
®
product. The charging indicator will light red.
3. When the product is fully charged, the indicator turns green.
7.2 Electric swatter mode
1. Slide the power switch (6) to the ON1 position. Press and hold the high-voltage grid but-
ton (5) when using, the working indicator lights up to indicate the metal grid is electrically
charged.
2. Wave the swatter toward the insect. Once the insect touches the grid, there will be a short
crackling sound and a brief blue spark.
3. Release the button (5) to stop the swatter. The working indicator will turn off. (Note: Do not
touch the metal grid at this time as there is still residual voltage on the metal grid.)
4. Switch off the power by moving the power switch to the OFF position.
7.3 UV lamp mode
1. Connect the product to a charger.
2. Slide the power switch to the ON2 position, the UV light will attract insects.
3. Rotate the handle of the product 180 degrees and place it on the table or hang it on a hook.
Tips:
– If there is no obvious effect on the insects or the purple light becomes dark, the battery
is low and needs to be recharged. Make sure the power switch is in the OFF position
before charging.

8 Cleaning and care

Important:
– Do not use aggressive cleaning agents, rubbing alcohol or other chemical solutions.
They damage the housing and can cause the product to malfunction.
– Do not immerse the product in water.
1. Always switch off and disconnect the power supply to the appliance before cleaning.
2. Clean the product with a dry, fibre-free cloth.
9 Disposal
This symbol must appear on any electrical and electronic equipment placed on the
EU market. This symbol indicates that this device should not be disposed of as
unsorted municipal waste at the end of its service life.
Owners of WEEE (Waste from Electrical and Electronic Equipment) shall dispose
of it separately from unsorted municipal waste. Spent batteries and accumulators,
which are not enclosed by the WEEE, as well as lamps that can be removed from
the WEEE in a non-destructive manner, must be removed by end users from the
WEEE in a non-destructive manner before it is handed over to a collection point.
Distributors of electrical and electronic equipment are legally obliged to provide free take-back
of waste. Conrad provides the following return options free of charge (more details on our
website):
in our Conrad offices
at the Conrad collection points
at the collection points of public waste management authorities or the collection points set
up by manufacturers or distributors within the meaning of the ElektroG
End users are responsible for deleting personal data from the WEEE to be disposed of.
It should be noted that different obligations about the return or recycling of WEEE may apply in
countries outside of Germany.

10 Technical data

10.1 Power supply

Input.............................................. 5 V/DC 1 A via USB-C
Rechargeable battery ................... 18650 Lithium, 1200 mAh
port on the handle of the Charging time ............................... approx. 3 hours
®
10.2 UV lamp
UV light ......................................... 4 pcs SMD
Frequency range .......................... 360-400 nm
Radiation power ............................ 80-100 mW
10.3 Other
Cable length ................................. 1 m
Protection class ............................ II
Operating conditions ..................... 0 to +40 °C, 20 – 80 % RH (non-condensing)
Storage conditions ........................ -20 to +50 °C, 5 – 90 % RH (non-condensing)
Dimensions (W x H x D) ............... 430 x 230 x 46 mm
Weight .......................................... 260 g
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com). All rights in-
cluding translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in electronic data
processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited. This publication
represents the technical status at the time of printing.
Copyright 2025 by Conrad Electronic SE.
®
*3365421_V3_0525_02_dh_mh_en