Seite 3
MODEL: HXTC-3WD This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation of our user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won't inform you again if there are any technology or software updates on our product.
6. Do not alter this product in any manner. 7. Do not lift the product directly with a forklift or tow with any mechanical devices. MODEL AND PARAMETERS Model HXTC-3WD Shelve Type W-shaped(Double-sided) Number of Shelves Max. Capacity 110lbs/per shelf...
STRUCTURE DIAGRAM Lateral Plate Document Rack Book Storage Area Wheels(With Lock) Wheels(Without Lock) PARTS LIST Lateral Plates x1 Lateral Plates x1 ① Book Storage Panels x6 Bookshelf Backboards x3 - 3 -...
Seite 6
② Bookshelf Backboards x3 Wheels(Without Lock) x2 Wheels(With Lock) x2 Bookends x1 Document Rack x1 Hex key x1 Hat nuts(M6) x28 Bolts(M6*8) x28 Wrenchs(10+19mm) x2 - 4 -...
Seite 7
Bolts(M6*14) x42 User Manual x1 INSTALLATION NOTE: This installation is best done by two people. Step 1: Install the Book Storage Panel. Back ② M6 nuts M6*8 ① M6*14 ① ① - 5 -...
Seite 8
NOTE: Please do not tighten the bolts yet. Step 2: Install the Lateral Plates. Flat board surface M6*14 Step 3: After all parts are installed, adjust the angle of the frame and tighten all bolts. - 6 -...
Seite 9
Step 4: Install the Document Rack. M6*8+Hat Nuts Hat Nuts Step 5: Install the four wheels. Wheels (With Lock) - 7 -...
Seite 10
USING THE CASTER BRAKE ■ To lock the swivel casters with brake, step down the levers. ■ To unlock the swivel casters with brake, pull up the levers. MAINTENANCE 1. Clean the surface after each use . Please check and confirm that the cart is intact before each use. 2.
Seite 11
Manufacturer: Shanghaimuxinmuyeyouxiangongsi Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX E-CrossStu GmbH...
Seite 15
Ceci e st l e m ode d 'emploi d'origine. V euillez lire a ttentivement l'intégralité d u manuel a vant u tilisation. VEVOR s e r éserve l e d roit d 'interpréter clairement c e m anuel d'utilisation. L 'apparence d u p roduit d épend du p roduit que v ous avez r eçu. ...
CONSIGNES D E S ÉCURITÉ 1. I l e st i nterdit d e t ransporter d es personnes s ous quelque c ondition que c e s oit. 2. C onserver l e p roduit s ur des s urfaces planes. I l e st i nterdit de c harger des a rticles sur terrains ...
Seite 17
SCHÉMA D E S TRUCTURE Plaque l atérale Portedocuments Espace d e s tockage des l ivres Roues ( avec b locage) Roues ( sans b locage) LISTE D ES P IÈCES Plaques l atérales x 1 Plaques l atérales x 1 Panneaux ...
Seite 18
Panneaux a rrière p our étagères x 3 Roues ( sans b locage) x2 Roues ( avec v errou) x2 Serrelivres x 1 Portedocuments x 1 Écrous à c hapeau (M6) x 28 Clé h exagonale x 1 Boulons ( M6*8) x 28 Clés ...
Seite 19
Manuel d 'utilisation x 1 Boulons ( M6*14) x 42 INSTALLATION REMARQUE : I l e st p référable q ue cette i nstallation soit e ffectuée par d eux personnes. Étape 1 : I nstallez le p anneau de r angement des l ivres. écrous M 6 M6*8 M6*14 ...
Seite 20
REMARQUE : N e s errez pas e ncore les b oulons. Étape 2 : I nstallez les p laques latérales. Surface d e p lanche plate M6*14 Étape 3 : U ne fois t outes les p ièces installées, a justez l'angle d u c adre e t serrez t ous l es b oulons. ...
Seite 21
Étape 4 : I nstallez le p ortedocuments. Écrous à c hapeau M6*8+ Noix d e c hapeau Étape 5 : I nstallez les q uatre roues. Roues (Avec s errure) 7 ...
Seite 22
UTILISATION D U F REIN DE R OULETTE ■ P our v errouiller les r oulettes pivotantes a vec frein, a baissez les l eviers. ■ P our déverrouiller l es r oulettes pivotantes a vec frein, t irez les l eviers vers l e h aut. ENTRETIEN 1. N ettoyez l a s urface a près chaque u tilisation. Veuillez ...
Seite 23
Fabricant : S hanghaimuxinmuyeyouxiangongsi A dresse : Shuangchenglu 8 03nong11hao1602A1609shi, b aoshanqu, shanghai 2 00000 CN. Importé e n A ustralie : SIHAO P TY LTD. 1 R OKEVA S TREET, ASTWOOD N SW 2122, Australie Importé a ux É tatsUnis : Sanven T echnology Ltd. S uite 250, 9 166 Anaheim P lace, Rancho ...
Seite 27
MODELL: HXTC-3WD Dies ist die Originalanleitung. Bitte lesen Sie alle Anweisungen sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen. VEVOR behält sich das Recht vor, die Bedienungsanleitung klar und deutlich zu interpretieren. Das Aussehen des Produkts hängt vom gelieferten Produkt ab. Bitte haben Sie Verständnis dafür, dass wir Sie nicht erneut über Technologie- oder Software-Updates informieren.
Produkt am Wegrollen zu hindern. 6. Verändern Sie dieses Produkt in keiner Weise. 7. Das Produkt nicht direkt mit einem Gabelstapler anheben oder mit einem mechanischen Geräte. MODELL UND PARAMETER Modell HXTC-3WD Regaltyp W-förmig (doppelseitig) Anzahl der Regale Max. Kapazität 110 Pfund/pro Regal...
Seite 31
Benutzerhandbuch x1 Schrauben (M6*14) x42 INSTALLATION HINWEIS: Diese Installation wird am besten von zwei Personen durchgeführt. Schritt 1: Installieren Sie das Buchaufbewahrungspanel. Zurück M6 Muttern M6*8 M6*14 - 5 -...
Seite 32
HINWEIS: Bitte ziehen Sie die Schrauben noch nicht fest. Schritt 2: Installieren Sie die Seitenplatten. Flache Plattenoberfläche M6*14 Schritt 3: Nachdem alle Teile montiert sind, passen Sie den Winkel des Rahmens an und Ziehen Sie alle Schrauben fest. - 6 -...
Seite 33
Schritt 4: Installieren Sie das Dokumentenregal. M6*8+Hutmuttern Hutmuttern Schritt 5: Montieren Sie die vier Räder. Räder (Mit Schloss) - 7 -...
VERWENDUNG DER ROLLENBREMSE ÿ Zum Feststellen der Lenkrollen mit Feststellbremse die Hebel nach unten treten. ÿ Zum Entriegeln der Lenkrollen mit Feststellbremse die Hebel nach oben ziehen. WARTUNG 1. Reinigen Sie die Oberfläche nach jedem Gebrauch. Bitte überprüfen Sie vor jedem Gebrauch, ob der Wagen intakt ist. 2.
Seite 35
Hersteller: Shanghaimuxinmuyeyouxiangongsi Adresse: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, Shanghai 200000 CN. Importiert nach AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australien Importiert in die USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited, Britische Republik Büro 147, Centurion House, London Road, Staines-upon- Thames, Surrey, TW18 4AX...
Seite 37
CARRELLI PORTA LIBRI MODELLO: HXTC-3WD...
Seite 39
MODELLO: HXTC-3WD Queste sono le istruzioni originali, si prega di leggere attentamente tutte le istruzioni del manuale prima di utilizzare il prodotto. VEVOR si riserva la piena interpretazione del manuale utente. L'aspetto del prodotto dipenderà dal prodotto ricevuto. Vi preghiamo di non informarvi ulteriormente in caso di aggiornamenti tecnologici o software relativi al nostro prodotto.
6. Non alterare in alcun modo il prodotto. 7. Non sollevare il prodotto direttamente con un carrello elevatore o trainarlo con qualsiasi mezzo meccanico dispositivi. MODELLO E PARAMETRI Modello HXTC-3WD Tipo di ripiano A forma di W (bifacciale) Numero di ripiani Capacità massima...
SCHEMA DELLA STRUTTURA Piastra laterale Portadocumenti Area di stoccaggio dei libri Ruote (con bloccaggio) Ruote (senza bloccaggio) ELENCO DEI PEZZI Piastre laterali x1 Piastre laterali x1 Pannelli posteriori per libreria x3 Pannelli portaoggetti per libri x6 - 3 -...
Seite 42
Pannelli posteriori per libreria x3 Ruote (senza bloccaggio) x2 Ruote (con bloccaggio) x2 Fermalibri x1 Portadocumenti x1 Dadi a cappello (M6) x28 Chiave esagonale x1 Bulloni (M6*8) x28 Chiavi (10+19 mm) x2 - 4 -...
Seite 43
Manuale utente x1 Bulloni (M6*14) x42 INSTALLAZIONE NOTA: è consigliabile che questa installazione venga eseguita da due persone. Fase 1: Installare il pannello di archiviazione dei libri. Indietro Dadi M6 M6*8 M6*14 - 5 -...
Seite 44
NOTA: non stringere ancora i bulloni. Fase 2: installare le piastre laterali. Superficie piana della tavola M6*14 Fase 3: Dopo aver installato tutte le parti, regolare l'angolazione del telaio e stringere tutti i bulloni. - 6 -...
Seite 45
Fase 4: Installare il portadocumenti. M6*8+dadi a cappello Noci del cappello Fase 5: Installare le quattro ruote. Ruote (Con serratura) - 7 -...
Seite 46
UTILIZZO DEL FRENO DELLE ROTAIE ÿ Per bloccare le ruote girevoli con freno, abbassare le leve. ÿ Per sbloccare le ruote girevoli con freno, tirare le leve verso l'alto. MANUTENZIONE 1. Pulire la superficie dopo ogni utilizzo. Si prega di controllare e confermare che il carrello sia integro prima di ogni utilizzo. 2.
Seite 47
Produttore: Shanghaimuxinmuyeyouxiangongsi Indirizzo: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Importato in AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Importato negli USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Ufficio 147, Centurion House, London Road, Staines- RAPPRESENTANTE DEL REGNO UNITO upon-Thames, Surrey, TW18 4AX...
Seite 49
CARRITOS D E L IBROS MODELO: H XTC3WD...
Seite 51
CARRITOS D E L IBROS MODELO: H XTC3WD Estas s on l as instrucciones o riginales; lea a tentamente todas l as instrucciones d el m anual antes d e utilizarlo. V EVOR se r eserva el d erecho de interpretar s u m anual de u suario. La a pariencia del p roducto dependerá del ...
INSTRUCCIONES D E S EGURIDAD 1. E stá p rohibido transportar p ersonas bajo c ualquier condición. 2. M antenga e l p roducto s obre superficies n iveladas. Está p rohibido cargar a rtículos sobre é l. terrenos i rregulares y m ontañosos. E l p roducto p uede volverse i nestable y v olcarse si almacenarse ...
Seite 53
DIAGRAMA D E E STRUCTURA Placa l ateral Estante p ara d ocumentos Área d e a lmacenamiento de l ibros Ruedas ( con b loqueo) Ruedas ( sin b loqueo) LISTA D E P IEZAS Placas l aterales x 1 Placas ...
Seite 54
Tableros d e e stantería x3 Ruedas ( sin b loqueo) x2 Ruedas ( con b loqueo) x2 Sujetalibros x 1 Estante p ara d ocumentos x1 Llave h exagonal x 1 Tuercas d e s ombrero (M6) x 28 Pernos ( M6*8) x 28 Llaves ...
Seite 55
Manual d e u suario x1 Pernos ( M6*14) x 42 INSTALACIÓN NOTA: E sta i nstalación se r ealiza mejor e ntre dos p ersonas. Paso 1 : I nstale el p anel de a lmacenamiento de l ibros. Atrás Tuercas M 6 M6*8 M6*14 5 ...
Seite 56
NOTA: N o a priete los t ornillos todavía. Paso 2 : I nstale las p lacas laterales. Superficie d e t ablero plano M6*14 Paso 3 : D espués de i nstalar todas l as piezas, a juste el á ngulo del m arco y Apriete t odos l os t ornillos. ...
Seite 57
Paso 4 : I nstale el e stante para d ocumentos. M6*8+Tuercas d e s ombrero Tuercas d e s ombrero Paso 5 : I nstale las c uatro ruedas. Ruedas (Con c erradura) 7 ...
Seite 58
USO D EL F RENO DE R UEDAS ■ P ara b loquear las r uedas giratorias c on freno, b aje las p alancas. ■ P ara desbloquear l as r uedas giratorias c on freno, t ire de l as palancas h acia arriba. MANTENIMIENTO 1. L impie l a s uperficie d espués de c ada uso. Por ...
Seite 59
Fabricante: S hanghaimuxinmuyeyouxiangongsi D irección: Shuangchenglu 8 03nong11hao1602A1609shi, b aoshanqu, shanghai 2 00000 CN. Importado a A US: SIHAO P TY LTD. 1 R OKEVA S TREET, EASTWOOD, N SW 2122, Australia Importado a E E. UU.: S anven Technology L td. Suite 2 50, 9166 A naheim Place, Rancho ...
Seite 63
MODEL: HXTC-3WD To jest oryginalna instrukcja, przed użyciem należy uważnie przeczytać wszystkie instrukcje. VEVOR zastrzega sobie jasną interpretację naszej instrukcji obsługi. Wygląd produktu będzie zależał od produktu, który otrzymałeś. Prosimy o wybaczenie, że nie poinformujemy Cię ponownie, jeśli w naszym produkcie pojawią...
6. Nie modyfikuj tego produktu w żaden sposób. 7. Nie należy podnosić produktu bezpośrednio wózkiem widłowym ani holować go przy użyciu jakichkolwiek urządzeń mechanicznych. urządzenia. MODEL I PARAMETRY Model HXTC-3WD Typ półki W kształcie litery W (dwustronny) Liczba półek 110 funtów/półka Maksymalna pojemność...
SCHEMAT STRUKTURY Płyta boczna Półka na dokumenty Miejsce do przechowywania książek Koła (z blokadą) Koła (bez blokady) LISTA CZĘŚCI Płyty boczne x1 Płyty boczne x1 Tylne tablice regałów x3 Panele do przechowywania książek x6 - 3 -...
Seite 66
Tylne tablice regałów x3 Koła (bez blokady) x2 Koła (z blokadą) x2 Półka na dokumenty x1 Podpórki do książek x1 Klucz imbusowy x1 Nakrętki kapeluszowe (M6) x28 Śruby (M6*8) x28 Klucze (10+19mm) x2 - 4 -...
Seite 67
Instrukcja obsługi x1 Śruby (M6*14) x42 INSTALACJA UWAGA: Instalację najlepiej wykonać w dwie osoby. Krok 1: Zainstaluj panel do przechowywania książek. Z powrotem Nakrętki M6 M6*8 M6*14 - 5 -...
Seite 68
UWAGA: Proszę nie dokręcać jeszcze śrub. Krok 2: Zamontuj płyty boczne. Płaska powierzchnia deski M6*14 Krok 3: Po zamontowaniu wszystkich części należy dostosować kąt ramy i dokręć wszystkie śruby. - 6 -...
Seite 69
Krok 4: Zainstaluj półkę na dokumenty. M6*8+Nakrętki kapeluszowe Kapeluszowe orzechy Krok 5: Zamontuj cztery koła. Koła (Z zamkiem) - 7 -...
UŻYWANIE HAMULCA KÓŁEK Aby zablokować kółka obrotowe z hamulcem, należy nacisnąć dźwignie w dół. Aby odblokować kółka obrotowe z hamulcem, należy pociągnąć dźwignie do góry. KONSERWACJA 1. Wyczyść powierzchnię po każdym użyciu. Przed każdym użyciem należy sprawdzić i potwierdzić, czy wózek jest nienaruszony. 2.
Seite 71
Producent: Shanghaimuxinmuyeyouxiangongsi Adres: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, szanghaj 200000 CN. Importowane do AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia Importowane do USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Biuro REP WIELKIEJ BRYTANII 147, Centurion House, London Road, Staines-upon- Thames, Surrey, TW18 4AX...
Seite 75
MODEL: HXTC-3WD Dit is de originele handleiding. Lees alle instructies zorgvuldig door voordat u het product gebruikt. VEVOR behoudt zich het recht voor om de gebruiksaanwijzing duidelijk te interpreteren. Het uiterlijk van het product is afhankelijk van het product dat u hebt ontvangen. Neemt u het ons niet kwalijk dat we u niet meer op de hoogte stellen van eventuele technologische of software-updates voor ons product.
6. Breng op geen enkele wijze wijzigingen aan in dit product. 7. Til het product niet rechtstreeks op met een vorkheftruck of sleep het met een mechanische trekhaak. apparaten. MODEL EN PARAMETERS Model HXTC-3WD Planktype W-vormig (dubbelzijdig) Aantal planken Maximale capaciteit...
Seite 79
Gebruikershandleiding x1 Bouten (M6*14) x42 INSTALLATIE LET OP: Deze installatie kan het beste door twee personen worden uitgevoerd. Stap 1: Installeer het boekenopslagpaneel. M6 moeren M6*8 M6*14 - 5 -...
Seite 80
LET OP: Draai de bouten nog niet vast. Stap 2: De zijplaten installeren. Vlak bordoppervlak M6*14 Stap 3: Nadat alle onderdelen zijn geïnstalleerd, past u de hoek van het frame aan en Draai alle bouten vast. - 6 -...
Seite 81
Stap 4: Installeer het documentenrek. M6*8+Hoedmoeren Hoednoten Stap 5: Monteer de vier wielen. Wielen (Met slot) - 7 -...
Seite 82
GEBRUIK VAN DE CASTERREM ÿ Om de zwenkwielen met de rem te vergrendelen, duwt u de hendels naar beneden. ÿ Om de zwenkwielen met de rem te ontgrendelen, trekt u de hendels omhoog. ONDERHOUD 1. Reinig het oppervlak na elk gebruik. Controleer en bevestig vóór elk gebruik dat het winkelwagentje intact is.
Seite 83
Fabrikant: Shanghaimuxinmuyeyouxiangongsi Adres: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Geïmporteerd naar AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australië Geïmporteerd naar de VS: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. T.a.v. YH Consulting Limited VK REP Kantoor 147, Centurion House, London Road, Staines- upon-Thames, Surrey, TW18 4AX...
Seite 87
MODELL: HXTC-3WD Detta är originalinstruktionerna, vänligen läs alla instruktioner noggrant innan du använder produkten. VEVOR förbehåller sig en tydlig tolkning av vår användarmanual. Produktens utseende ska vara beroende av den produkt du mottagit. Vi ber om ursäkt för att vi inte kommer att informera dig igen om det finns några teknik- eller programuppdateringar för vår produkt.
6. Ändra inte denna produkt på något sätt. 7. Lyft inte produkten direkt med en gaffeltruck eller bogsera med någon mekanisk enheter. MODELL OCH PARAMETRAR Modell HXTC-3WD Hylltyp W-formad (dubbelsidig) Antal hyllor Maxkapacitet 110 pund/per hyllplan Material Stål...
Seite 91
Användarmanual x1 Bultar (M6*14) x42 INSTALLATION OBS: Denna installation utförs bäst av två personer. Steg 1: Montera bokförvaringspanelen. Tillbaka M6-muttrar M6*8 M6*14 - 5 -...
Seite 92
OBS: Dra inte åt bultarna ännu. Steg 2: Montera sidoplattorna. Plan yta på skivan M6*14 Steg 3: När alla delar är monterade, justera ramens vinkel och dra åt alla bultar. - 6 -...
Seite 93
Steg 4: Installera dokumentstället. M6*8+hattmuttrar Hattnötter Steg 5: Montera de fyra hjulen. Hjul (Med lås) - 7 -...
ANVÄNDA HJULBROMSEN ÿ För att låsa länkhjulen med broms, trampa ner spakarna. ÿ För att låsa upp länkhjulen med broms, dra upp spakarna. UNDERHÅLL 1. Rengör ytan efter varje användning. Kontrollera och bekräfta att vagnen är intakt före varje användning. 2.
Seite 95
Tillverkare: Shanghaimuxinmuyeyouxiangongsi Adress: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN. Importerad till Australien: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australien Importerad till USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730 YH CONSULTING LIMITED. C/O YH Consulting Limited Storbritanniens republikaner Kontor 147, Centurion House, London Road, Staines- upon-Thames, Surrey, TW18 4AX...