Wild M 11 Gebrauchsanweisung
Vorschau ausblenden
Andere Handbücher für M 11:
- Gebrauchsanweisung (28 Seiten) ,
- Gebrauchsanweisung (28 Seiten)
Verwandte Anleitungen für Wild M 11
Inhaltszusammenfassung für Wild M 11
- Seite 1 Microscope Microscope Mikroskop Microscopio WILD M 11 Instructions Mode d'emploi Gebrauchsanweisung Instrucciones para el uso WILD HEERBRUCG SWITZERLAND...
- Seite 2 Page Contents Unpacking Assembly Setting up the illumination Mirror Mains (line) lamp M Socket lamp Transformer Attachable Köhler lamp Q Adjusting the binocular tube Care of the microscope Packing numbers quoted in the text refer fold-out illustration page U npacki Table matiéres page...
- Seite 3 Optics holder I Fine focussing protection Changing tubes The optics holder (a) has a double function during Monocular tube is screwed on to microscope body, transport. It stores the objectives and eyepieces is rotatable through 3600. It is removed also takes the load off the fine focussing mechanism.
- Seite 4 Loosen clamping screw (5) of adapter. Press bino- Fitting mechanical stage Place mechanical stage on microscope stage so cular tube against spring bolt of clamping screw (5) and lower it into position, Turn tube to desired that guide pins (b) of former engage corresponding position...
- Seite 5 (2) in opposite direc- tions. Mise en place du condenseur (Statif Mise en place condenseur (Statif Pour Ie microscope M 11, type A. la platine Descendre Iégérement le porte-condenseur "aide munie d'une douille porte-condenseur fixer mouvement crémaillére...
- Seite 6 Light sources The 6V120W Köhler lamp is also attached via socket, Mirror, mains (line) lamp or socket lamp may be but in addition ts secured from below, with a large plugged into socket in base of microscope milled screw Note: With certain combinations...
- Seite 7 Mirror Mains (line) lamp Set plane side of mirror to face light. Fully raise Connect lamp to mains (line) supply, Switch condenser by means Of condenser drive (2) and lamp by turning ridged collar Fully raise con- open condenser diaphragm (6) completely.
- Seite 8 Socket lamp P, 6Vf5W Place frosted filter over empty tube. using a IOX objective, focus image of specimen on filter. Lower voltage selector transformer mains (line) voltage. Connect lamp to transformer condenser until lamp filament is imaged on filter, transformer to mains (line).
- Seite 9 Regulating transformer f, Köhler lam p Q, 6Vf20W Changing bulb Loosen both centring screws (a) of socket lamp by Connect cable 01 lamp to a secondary output of trans- about turns. Press collector mount against former, Set transformer to mains (line) voltage, counterspring...
- Seite 10 Step transformer Köhler lamp Q, 6Vf20W Attachable Köhler lamp Q, 6V/20W Connect cable of lamp to 6V secondary output Select objectiver raise condenser (with front transforrner. Remove fuse (b) from voltage selector lens) to highest position Open condenser dia- by pressing it in gently and turning it to the left.
- Seite 11 Open field diaphragm (9) until it just disappears Adjusting condenser diaphragm from field of view. If it is not possible to illuminate Remove eyepiece and look into empty tube from whole field, front lens of the condenser must distance of about 10 im (25 em). Slowly close con- removed and diaphragm...
- Seite 12 —O Adjusting binocular tube Changing bulb Withdraw lamp socket from Köhler illuminator. Press Infer-pupillary distance: Slide left eyepiece bulb against socket and remove from bayonet sideways until a single circular field is seen. slight turn to left, Fit new bulb, replace lamp socket Anisometropia:...
- Seite 13 Do not grease or oil the mechanical parts, If the instrument no longer functions satisfactorily ask the advice of a specialist or your local WILD represen- tative. Soins donner å Itinstrument Protéger l'instrument des poussiéres, de I'humidité...
- Seite 14 Packing If the instrument has to be re-packed for transportation, the objectives are unscrewed from the nosepiece, the eyepieces removed from the tubes, and all stored in the optics holder. The mirror or socket lamp can remain in the microscope base, Important: The optics holder is fitted between the base and the stage, in order to protect the fine focussing...
- Seite 15 Guarantee We guarantee the quality of each of our instruments, Our guarantee covers all faults in materials and manu- facture. It does not, however, cover damage resulting from careless or improper handling. Garantie Dans nos prestations, nous répondons de la qualité des instruments, mais cette garantie s'étend...
- Seite 17 WILD -HEERBRUCG 296066 -VII. 70— Printed in Switzerland Wild Heerbrugg Limited CH•9435 Heerbruggj Switzerland Optical Precision Instrument Makers Telephone (071) 722433 / 72 1433 Telegrams: Wico Heerbrugg / Telex: 77191...