Encryption Function; Setting; Bluetooth Switch - Retevis Rt29D Bedienungsanleitung

Receive and reply Individual Call
Private Call is one to one calling.
When Receiving a Private Call:
1.LED indicator turns green.
2.Hold the transceiver vertically and keep about
1~2inches(2.5-5.0cm) away from mouth.
3. Press PTT key to respond to the call, LED indicator turns red.
4. Release PTT key to receive.
Receive All Call
All Call is a call from an individual transceiver calls all transceivers at the same channel. It is used to announce something important that
users must pay special attention to.
When received all call, LED indicator turns green.
Notice: when receiving all call, if you turn to another channel, the transceiver stop to receive all call. During the all call, you can not use
any re-programmed key until the call finished.
Launch a Transceiver Call
You can choose a channel, user ID or talking group ID with following methods.
●Channel Knob
Launch a Group Call
To launch a group call, the transceiver must be configured as belonging to that group.
1.Rotate channel knob, using activated group ID to select the talking group.
2.Hold the transceiver vertically and keep about 1~2inches(2.5-5.0cm) 15 away from mouth.
3.Press PTT key to launch the call, the LED indicator turns red.
4. Release PTT key to receive, when the target transceiver is responding, LED indicator turns green.
Launch a Private Call
1. Rotate channel knob, using activated user's ID to select channel.
2.Hold the transceiver vertically and keep about 1~2inches(2.5- 5.0cm) away from mouth.
3. Press PTT key to launch the call, the LED indicator turns red.
4. Release PTT key to receive, when the target transceiver is responding, LED indicator turns green.
Launch All Call
This functions allows you to transmit to all users in same channel. The transceiver must be programmed with this function, so that you can
send information to every user who are under the channel.
1.Rotate channel knob, using activated all call talking group ID to select channel.
2.Hold the transceiver vertically and keep about 1~2inches(2.5- 5.0cm) away from mouth.
3.Press PTT key to launch the call, the LED indicator turns red.
Scan Function (Carrier Scan)
1. Use programming software to set PF1/PF2 as scan function.
2. Long press the scan button, the transceiver will give a "di"sound to active scan function, it will stop when a valid signal has been scanned.
After the signal disappears in 5 seconds , scan starts again.
Long press the scan button again, the transceiver will give a "di di" sound to turn off the scan function.
Power reporting function
Through the programming software, define PF1/PF2 as the electricty reporting function; Long press the electricty reporting definition key,
and the transceiver will give "Di" sound and report the current percentage power.

Encryption Function

Encryption Setting (This function is effective for digital mode only)
According to the programming software setting, there are 10 groups at most to preset group encryption or encryption key (10 Byte) With
pre-programmed key to start up / shut down encryption function.

Setting

Setting Squelch level
You can adjust the transceiver squelch level, filter low signal
strength(unwanted calls) or the the channel that background noise is higher than the channel common values.
Set: 1-10 levels,the higher the level, the deeper the squelch,squelch deep filtration (unwanted) calls or background noise. However, a call
from a remote location may be also filtered out.
Setting Power Level
You can set each channel power in High /Middle/Low level.
Setting: Set high power to communicate with transceivers in far area. Set middle/low power to communicate with transceivers in near area.
Press pre-programmed "High /Middle/Low power" selection key.

Bluetooth Switch

Define PF1/PF2 as a Bluetooth switch through the programming software (default button is PF2);
Long press the Bluetooth switch definition key, hear a beep to turn on the Bluetooth function, and the blue light will flash.
Long press the Bluetooth definition button again, and turn off the Bluetooth function when you hear a "didi" beep.
When connected, the blue light stops flashing; when disconnected, the blue light flashes.
5