Commodore 1084 Bedienungsanleitung Seite 3

EngliSh
Introduction
Your monitor has been designed and
manufactured the highest standards.
and subjecn to rigorous testing. Provided it
is properly operated and maintained it '&ill
perform well for manyyears
This colour monitor is suitable for use with
home and personal computers. video
recorders, LaserVision ptayers and TV
Tuners.
Connectio n to themains For uK only)
Your new monitor is designed to operate
from an a.c. mains supply of 220-240 volts,
50 Hz Stabilising circuits ensure
satisfactory performance within normal
supply variations.
Important: This apparatus must be
earthed. Ttüs Canbe achieved by fitting a
3 pin plug. The wires in the earthed
mains lead are coloured accordnq to
the following code:
- NEUTRAL
BLUE
BROWN LIVE
GREEN/YELLOW- EARTH
If the mains plug (or adaptor) contains a
fuse. the value Ofthis fuse should be
3 Amp. Alternatively, if another type Of
plug (not fused) is used. the fuse at the
distribution board should not be greater
than 5 Amp.
If the colours of the wires in the mains
lead do not correspond with the
coloured markings identifying the
terminals in y0Lr plug, proceed as
follows
The BLUE *4re should be connected
the terminal marked 'N' or coloured
black.
The BROWN wire should be connected
to the temnal marked 'L' Or coloured
red.
The GREEN and YELLOW wire must be
connected to the terminal in the
marked by 'E' or the earth syrnbol 4. Or
coloured green or green and yellow
Before replacing the plug cover, make
certain that the cord grip is clamped
over the sheathof the lead- not simply
over the three
positioning 'Ventilation
In ortfir to prevent overheatirvg, ensure
that the ventilation openings
are not covered.
The monitor should not be placed near a
source of heat nor on a soft surface s.nce
this would block the ventilation
the bottom.
Movable support
You can tilt the monitor into a convenient
position with regard to the computer by
using the movable support.
Connection to the mains
You can connect your monitor to a mains
Sdtage of between 220 and 240 V. If the
mains voltage in your home is different
from this. consult your dealer.
Connections (rear pmel)
for input Of video and audio
connector is marked wi!h its function
QQAO
to
CVBS/L (Luminance) IN (Phono type)
CVBS (composite signal) or Luminance
input phono plug type.
For connection of a computer or other
CVBS sources.
CHROMA IN (phono type)
Chroma (colour signal) of the
plug type. For connection of a
compu ten
AUDIOIN (Phono type)
For connection of a Signal source with a
sound (audio) signal output
LCA,'CVBS switch
With the LCA•'CVBS switch
either choose the LCA signal or the CVBS
signal (via
the monitor
TTL R GB i nput (8 pin DIN type 2WVL
For connection of a computer with a
slots on
Contwction
Hædphon.s
On the lett side Of the rnonitor
a
Operation
Each
Switch"g on O
• Press button O (LED lights 10).
off O
• Press button O •gain
Picture and sow'd
For an optimum adjustment of the video artd audio input signa's various controls are
• flap@
you can
phono
CVBS + RGB linear + Audio input
(Euroconnector type)
For connection
Cornputer. LaserVisim Player. TV Tuner,
(left panel)
etc equ$ped
will
It you connect both RGB hputs
for
sirnultaneousb'
NtomaticaVy has priority over the linear
RGB
After switching Otfor removing the
connection cable trom the TTL Source.
RGB linear will be
Furthermore you can connect a CVBS
source
Tuner.etc.) to oneof the CVBSinput
sockets. but rx)t on both input sockets
simultaneously because this might result in
*ture
controls
Of a Video
with a Euroconnector.
the TTL RGB
_
in.
(computer. Video Recorder. TV
esturbance.
POW R