Werbung
Verfügbare Sprachen
Verfügbare Sprachen
Overload of the motor by too large diameters, too much feed or by
blunt tools is, of course, to be avoided. Damages occurring to non-
observance of these requirements are excluded from the guaranty
and from any other liability.
The length of the tools must be limited in such a way that after com-
pletion of the routing operation when the locking of the routing
depth has been released, or when the routing depth was limited by
means of the depth stop, the tools do not protrude over the bearing
face of the base plate when the workpiece
Attention:
Danger
of accidents!
ter is given by the hole in the base plate.
4.4 Handling
and operation
The portable
electric
router
with the on-and-off
switch and at the turning clamping handle for
the routing depth. Do never work with the machine by using only
one hand! Both hands must grip both the handles.
without
base plate!
The handle
positioned
opposite
led and serves for fixing the motor at any height position beween
O and 80 mm. Additional
locking of the height can be done by
means of the existing
flat leaf screw.
For adjusting
the routing
depth place the router onto the workpiece
and fix it in position by means of the turning handle. This position
corresponds
with the zero-position
stage depth stop then provides
sired routing depth by means of the scale existing at the motor. At
the depth stop there is an adjustable stop plate with stop screw. It is
possible to either adjust the surface of the screw head to the de-
sired routing
depth by adjusting
de of the stop plate. In order to make sure that the stop unit (screw
and plate) cannot shift, the clampable plate must be placed against
the stop plate and clamped in position. The clamping plate with the
clamping screw can be swivelled. Therewith there are two routing
depths.
The outside diameter of the base plate (routing basket) with the in-
side-positioned
copying
ring seat has been manufactured
a way that it is precisely
centric
machine can be placed and guided at a fence or at a template at
the inside or at the outside.
fastened in the prisms of the base plate and which is protuding to
the right or to the left, grooves
Use
diameter
Softwood
Coated
coreboard
Hardwood
Coated
chipboard
Plastic
material
(polysterene,
polyethylene,
acrylic glass)
is being moved back.
The maximum
diameter
of the rou-
must be gripped
at the switch
And never work
the switch
handle can be swivel-
on the scale. The existing two-
for the possibility
to adjust the de-
the screw, or else only the stop si-
to the router tool carrier
so that the
With an adjustable
fence which can be
and rebates
can be routed. The co-
Adjustment of Speed:
Tool-
Step 1
11 600 min-l
10 OOO min-
10-16
18-24
25 - 35
10-16
18-24
25 - 35
10-16
18 - 24
25 - 35
10-16
18-24
25 - 35
10-16
18 - 24
x
25 - 35
x
pying ring serves for routing of all kinds of contours. For such work
the corresponding
4.5 Operation
and use of the electronic
The speed is infinitely variable between 10,000 and 18,000 min-l
by means of the control wheel of the full-wave (sine wave) electro-
nics. The numbers
only as a help for adjustment. The speed (rpm) is at
step 1
step 2
step 3
step 4
step 5
step 6
handle
Features and advantages of the control-electronics:
I. With the correctly
the speed of cut with: the material, the tool (HSS/HM) and the
tool
diameter.
2. The optimum
speed of cut provides
will facilitate the routing operation and increase the service life
of the tools.
3. The preselected speed will be kept by the automatic re-adjust-
ment of the electronic system.
4. The HM 18-E can start softly and without
The below table should serve as a help to find the right speed orthe
correct speed of cut respectively. It can, however, only be a recom-
mendation. The optimum speed depends on the changeability
the material
and also on the feed; this means
speed should best be tested by a trial routing operation.
Attention
In case of a cutting out of the circuit of the control electronics (short
circuit)
the idle running
min-l. In such a case the portable router must be immediately swit-
ched off! Further routing operations will then not be possible as at
the router shaft there will then ony be a minimum of torque (rou-
ting power).
in such
4.6 Dust
extraction
As a standard part included in the delivery the portable router is
equipped
with a dust extraction
traction. In order to serve environment
should
be used.
Speed steps
I —6
Step 2
Step 3
13200 min-l
x
x
x
x
x
x
x
template
are necessary.
control
1 - 6 indicated
on the control
approx. 10,000 min-l
approx 11,600 min-l
approx. 13,200 min-l
approx. 14,800 min-l
approx. 16,400 min-
approx. 18,000 min-l
preselected
speed
it is possible
for a neatly routed surface.
any jurking.
speed
may increase
to approx.
connection
for outside
and health, this possibility
Step 4
Step 5
14800 min-l
16400 min-l
x
x
x
x
x
x
x
x
x
x
x
wheel
are meant
to coordinate
It
of
that the selected
27,000
dust ex-
Step 6
18
min-l
x
x
x
x
x
x
x
x
5
Werbung
