Robus RHEMW-04 Kurzanleitung

PLUG-IN MICROWAVE & 3 STEP DIMMING SENSOR FOR HARBOUR EXPRESS
RHEMW-04
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. The Installation must be carried out by a qualified electrician. Product or a person
falling from height can cause serious personal injury. Please ensure suitable equipment is used by a competent person.
Note:
The luminaire must be disconnected before carrying out any insulation resistance testing. Product technical information and specification may
change over time without prior notification. For the latest technical information please visit our web site www.robus.com or robusdirect.com
-20°C < Ta < +40°C, 220-240V DC, Class II, IP20, Standby power 0.5
Detection Range: Radius 3m - Radius 4.5m (Ceiling Mounting height 3m)
Radius 5m - 8m (Wall Mounting height 1.8m)
Installation
1. Ensure mains supply is switched off before commencing work.
2. Safety note! The power supply cord must not be exposed to mechanical
damage.
3. Open the diffuser to access LED gear tray. Place sensor onto the place that
marked "Sensor" and lock two clips of sensor into the slots.
4. Connect the sensor to LED driver and terminals using quick fix connectors.
5. Configure sensor settings using the walk test method outlined below.
6. Refit LED plate and diffuser.
Walk testing can be carried out, with a slow walking pace, to determine the
detection area When the sensor detects movement, the load will be switched on for
the preset time. For the walk test set detection range to 100 or 50%, set delay time
to 5s and disable daylight sensor. When finished, set controls to desired levels.
Sensitivity: The size of the area where movement will be detected and able to
trigger the sensor. 100% detection area is also known as maximum sensitivity.
Hold time: The length of time the light will stay on at 100% after movement has not
been detected.
Daylight: When the ambient brightness is lower than the specific lux amount, the
sensor will work. When it's set to "disable", the sensor will detect motion regardless
of the ambient brightness.
Stand-by period: The period of time the light keeps output at low until hold time
elapsed. When it's preset as "+∞", the light always keep output at low if no
movement in the detection area and isn't switched off.
Stand-by Dimm level: The level brightness of light on the stand-by time: 10%,
30%.
Note: The detected surface of sensor cannot be shielded by metal objects. This
fitting has no user serviceable parts. If damaged, disconnect from mains and
discontinue use.
Sensor Settings Table
1. When key No.9 set off, the senor will work as on/off function.
ON
1 2 3
OFF
Hold-time
DIP switch
5S
30S
Sensitivity 1min
3min
DIP switch 1 2
100% 5min
10min
75%
50% 20min
25% 30min
Issue 1 240423
Unit(mm):
56
43.6 64
Wiring:
L
-
+
N
LED driver
VCC
GND
DIM
4 5 6 7 8 9
3 4 5
Daylight threshold
DIP switch 6 7 8
2Lux
10Lux
25Lux
50Lux
Disable
The daylight threshold is set to "2Lux/10Lux/25Lux/50Lux"
EN
1
With sufficient daylight, even
when motion detected,
light remains OFF
2. When key No.9 set on, the senor will work as dimming output/corridor function.
ON
OFF
DIP switch
Sensitivity
DIP switch 1
100%
50%
The daylight threshold is set to "10Lux/25Lux/50Lux, stand-by period is set to "10s/15min".
1
20.9
27
With sufficient daylight,
even when motion detected,
light remains OFF.
5
Sensor
After the stand-by period,
light turns off.
Installation figure:
Sensor Work ON OFF
Information for the Product user:
DIP switch 9
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use, recycling, and other forms of recovery of Waste Electrical and Electronic Equipment by returning this product at end of life
ON OFF Mode
to a collection centre for waste equipment or a civic amenity site or to a retail outlet from which you had purchased it or from where you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and to the environment if disposed of carelessly. It is important that it is separated from normal household
waste and recycled in the WEEE chain.
4. The "crossed out wheelie bin symbol" on a product indicates this equipment must not be disposed of in normal household waste but should be disposed of in accordance with
the local WEEE regulations.
2 3
With insufficient daylight, After people leave the detection area,
when motion detected, light ON. light remains 100% brightness within
hold time.
1 2 3 4 5 6 7 8 9
Hold-time Daylight threshold Stand-by period
2 3 DIP switch 4 5 DIP switch
5s Disable 0s
90s 50Lux 10s
5min 25Lux 15min
10min 10Lux +∞
2 3
With insufficient ambient brightness, Light keeps on 100%
light dims to 100% when motion within the hold time.
was detected.
Detection coverage：
Sensitivity: 50%
25%
100%
75%
Right
6
5
4
3
2
1
6 5 4 3 2 1 1 2 3 4 5 6
Front
Queen
1
2
3
4
5
The sensor was ceiling mount at 3m,
6
testing operator height 169cm,
walking speed 0.5m/s
Left
4
After the last detection and the preset
hold time elapsed, light turns off.
6 7
Stand-by
dimming level Sensor Work Dimming
DIP switch 8 DIP switch 9
10% 3 step dimming mode
30%
4
Light dims to standby level if no motion
detected after hold-time.
Wall
Left 9 8 7 6 5 4 3 2 1 1 2 3 4 5 6 7 8 9 Queen
1
2
3
4
5
6
7
8
9
Square
The sensor wall mounted at 1.8m,
testing operator height 169cm,
walking speed 0.5m/s
L.E.D lighting & Electrical Distribution Group Ltd
IRE: Nangor Road, Dublin 12, D12 E7VP, Ireland
UK: Bracknell Enterprise & Innovation Hub, Ocean
House, 12th Floor, The Ring, Bracknell,
Berkshire RG12 1AX, UK
Tel: +353 1 7099000
Fax: +353 1 7099060
Email: info@robus.com
Website: www.robus.com