PATLITE NE-24A Betriebsanleitung

PATLITE
NE-24A
TYPE
NE-24A) FL-Vt
NE
24 DC24V
it NE-24A-R
ODC24V
ou-y5
56
(25M)
PATLITE
Signal Beacons
INSTRUCTION MANUAL
NE-24A
TYPE
Thank you very much for purchasing our Patlite products
Notice to Customer
• Request the installation and wiring to be performed by a professional contractor if
construction work is involved
• prior to installation, read this manual thoroughly before using this product to ensure correct use
• In addition, please store this manual for future reference when performing
• Visit our homepage (https://www.patlite.com/) and download the "Complete Operation Manual: NE-24A" to
find out more about the operating method and features.
• If there are any questions concerning this product, refer to the contact information
contact your nearest PATLITE Sales Representative
CE Marking
• This product conforms to EN standards and shows the CE Marking This product
comply With the limits for a Class A device, pursuant to EMC DIRECTIVE
reasonable protection against harmful interference when the equipment is operated in a commercial environment
This product must not be used in residential areas
I Read this First (Safety Precautions)
A Warning II
Fa' ure to observe the following may result in death or serious injury
• To prevent from short-circuits or damage, observe the following'
-Be sure the power is disconnected before replacement or repair, including the replacement of the fuse
-use this product in a properly maintained condition. (Replace or repair if the globe, case, etc are damaged.)
• If installing this product requires construction work, ask a specialist in order to avoid fire, or personal
• When this product is used for security purposes, it should be inspected daily. In case a malfunction should occur,
it is recommended that you use this product together with other security products
• After installation, do not use this product to climb up onto the equipment with. Failure to comply will result in
product damage and/or falling Off the machinery
Failure to comply with the following
! physical l ossor damage.
• Be sure to put a fuse in the wiring circuit between the power source and equipment for protection
may result in product and/or equipment failure
• Be sure to prevent electrostatic damage due to discharge When working With this product for Wiring, exchanging units,
setting up parameters,etc by dischargingstatic electricity on your body,etc
• Do notdisassembleor detach duringoperation.
• DO not push on any internal parts when wiring.
2 Model Number Configuration
Model RatedVoltage
Assembly Model NE
24 24V
NE-24A-R
mp
.24 V DC • Red
3
Part Names and Outer Appearance
Globe
O-ring
Case
Name late
ø 56
(Without waterproof sheet)
Waterproof Sheet I Drill the mounting
Water roof Sheet
4
GA0000126 02
patlite
@
@ 57kY—
@ M4ta
35.5
en-R&
• Rd-n
: mm
nffi
4.5
13.3
(pNp F3YYR5)
4 Installation
• The following requirements
Install the signal light where excessive vibration is not present
Install the signal light on a sturdy surface
Install the signal light on a level surface
• When it is necessary to waterproof the backside of the installation
Digest Version
surface;
Provide a sealant coating around the nuts of the backside of the
installation surface
Provide a sealant coating around the wire exit hole, or use a
Cable Gland
After locking the globe, check that there is no gap between globe
and body. Being a gap may cause water intrusion or falling Off the
globe
(1) un Ock the globe by holding and rotating it in a
counter-clockwise
maintenance, repairs or inspections
(2) Drill the mounting holes(Ø4.5) from the top on the case.
(3) Peel Off the adhesive
apply it to the case.
at the end Of this document and
(4)Affixtheproduct totheinstallation s urface With screws andnuts(3)
(Installation screws and nuts are not included with this product.)
(5) After mounting the case, fit the g Obeby aligning the positioning (4)
marks and lock it by rotating in a clockwise direction
has been tested and found to
.lnstallation Dimensions
These limits are designed to provide
Unit : mm
wre
• When the Cable Gland is used, the hole must be large enough for it to fit through.
The recommended
screw size: M16x1 5; screw length: shorter than Ilmm;
injury outer diameter: less than 25mm;
material: plastic. (Torque 3N•m)
• This product
Caution
• Do not leave the product, or use it without globe Installed
• Do not apply excessive force when mounting/removing the globe Failure to comply will result in damage
• Use a soft cloth moistened with water to clean the globe or case. (Do not use thinner, benzine, gasoline or oil I)
points may result in injury,
• The waterproof sheet must be used before
• This product has a Imm thick waterproof
unevenness may cause a lack of waterproofing protection, it is recommended to apply sealant between the unit
If a fuse is not added, t
and the installation
5 Wiring
(1) Remove the globe by unscrewing it in a counter-clockwise
direction
(2) Connect the wires to the screwless
(3) Attach the globe by screwing it in a clockwise direction
• The terminals have no pola
Screwless
LED Unit Col
A minus driver etc is used to pry the lever slotofthe
Terminal Block open, by pushing straight onto the lever slot
(2) The stripped side of the lead wire is Inserted in the slot
(3) The driver is removed to release the lever (Check to make
sure the lead wire has been locked in place )
R Red
• Strip 8 mm of wire insulation from the wire to insert it in
the Terminal Block
Y Amber
• The minus driver blade should be at about 2mm by
O in Size
G Green
• Make sure the power is OFF before wiring. A short circuit may damage intemal circuits
A Caution
• Ensure the proper
Blue
• DO not pull the Wire out or push it into the case
• Be sure the wiring is done properly Any mistake in wiring may result in damage
White
• Be sure to put a fuse in the wiring circuit between the power source and equipment for protection If a fuse is not
added, it may result in product and/or equipment failure.
• DO not apply excessive
Notice Makesure thatthe wiresdo notsag internally. T hereis ariskthatthelightintensitymaybe reduced by hittingtheLED
Wiring Example
Wiring examples vary depending
unit: mm
(A) External Contact Drive
Mounting Holes
Ø45
(B) 1/0 unit Drive
(NPN Transistor)
Wire Exit Hole
ø 13.3
(C) 1/0 Unit Drive
Bottom View
(PNP Transistor)
holes from the top
$4.50 F v
($ 16) 5-11b"? $26
(2-$4.5 M4tac : 0.6N.m)
IA
AR-a
(NPNor PNP)I
L — en—X
DC24V IA
/Oazyh-
IA DC24V
-2
are necessary for proper installation:
direction, then lift it up
paper from the waterproof sheet and
Exit Hole
(Ø16) When the Cable Gland is used: Ø26
Installation Holes
(2- 5 M4 Screw Torque : 0 6N•m)
nsta lation Example
Cable Gland size is as f0110'.•.'s:
is for indoor use only (DO not use it outdoors )
installation
sheet at the bottom Of the case However, because installation
surface to maintain waterproof conditions
Screwless Terminal Block App icable Wire Sizes
Single: 0
terminal block
stranded:
Terminal Block Wiring meth
Wiring Example
voltage is used Improper voltage wil damage internal circuits
force to the screwless terrninal block during Wiring. It Will be the cause Of the failure
on the driving method
Fuse
External C Ontact
Fuse Rati
Supply
(Non-polar) [ External Contact Capacity
Current Capacity
Fuse
Volta e C ci
( Transistor (NPN or PNP)I
I Unit
Current Capacity
Supply
Withstand Voltage
Leakage Current
Fuse
DC24V
• No significant inrush current present.
Supply
llJnit
DC24V
5
6
(EN61000-6-4, EN61000-6-2)
UL508, CSA-C22.2 No.14
KC (KN61000-6-4, KN61000-6-2)
0.2—1.5mm2
AWG24æ16
en—RZ-xn
250VIA
Is? 50mA
vsæ35V
Ic 50mA
ve 35v
IL $ 0.1mA
6
S ecifications
Model
Rated Voltage
Current Consumption (Max.)
Mounting Direction
Operating Temperature Rang
(Relative Humidity)
Positioning
Mark
Protection Rating
Locked >
Mass
•1 Condition to satisfy IP66/67: Only when this product is installed with a Cable
Gland on a flat surface
Unlocked
• Conformity Standards
EMC Directive 000-6-4, EN61000
UL508, CSA-C22 2 No 14
KC (KN61000 6-4, KN61000-6-2)
• Low Voltage Directive (IEC/EN60947-5-1 ,EN62471)
• Conformity requirements for the IJL Standard:
• Maximum surrounding air temperature rating of 50 oc
• This product is designed for use on a flat surface for a Type 1 Enclosure.
• use a •class 2" power supply specifed in the guidelines under UL1310.
• For use in pollution Degree 2 Environment
• Conformity requirements for the CE Marking:
This product conforms to EN standards and shows the CE Marking
This product has been tested and found to comply with the limits for a Class A device, pursuant to EMC
DIRECT VE. These limits are designedto provide reasonableprotection against harmful interferencewhen the
equipment is operated in a commercial environment.
• Conformity to FCC Compliance:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to providereasonable protectionagainst harmful interference
When the equipment is operated in a commercial environment
radio frequency energy and, if not installed
harmful interference to radio communications Operation of this equipment in aresidential area is likely to cause
harmfu interference in which case the user will be required to correct the interference at his own expense
(Note) • Dimensions and specifications may change without notice due to
surface
continual product improvement.
• PATL TE and the PATLITE logo is a trademark, or registered
trademark of the PATLITE Corporation of Japan and each country
(Importer for EU)
PATLITE Europe GmbH Am Soeldnermoos 8, D-85399 Hal bergmoos, Germany
1 5mrn2
AWG24 - 16
250VIA
]
s250mA
vs235V
Ic250mA
Vc235V
II-SO. 1 mA
NE-24A-CZI
DC 24V
26mA
-300C&+500C
IP65 NEMA TYPE4X, 13
0.06k
RoHSiE# (EN50581)
FCCPart 15 Subpart BClassA
(IEC/EN60947-5-1,EN62471)
[Ver2.1 (2018_07.27)]
-3
NE-24A-a
24V DC (Non-polar)
26mA
All Directions
-300C - +500C
(Less than 90%RH, Non-condensation)
P 65 NEMA TYPE 13
0 06kg
6-2) RoHS Directive (EN50581)
FCC Part 15 Subpart B Class A
This product must not be used in residential areas
The equipment generates, uses, and can radiate
and used in accordance With the instruction manual, may cause
6