Ballu BCH/R-1500 Kurzanleitung Seite 3

HOME
User Manual
Convector heater
220-240V 50-60Hz 1OOOW/1500W/2000w
Electrical control
BCH/R-1500/1800/2200
IMPORTANT SAFEGUARDS
PLEASE READ ALL INSTRUCTIONS BEFORE
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
RISK OF FIRE, ELECTRICAL SHOCK AND INJURYTO PERSONS OR PROPERTY, INCLUDING THE FOLLOWING
When switching on the appliance for the first time, allow it to run at full power for about two hours to get
rid of the unpleasant smell. Make sure that the room in which the appliance is located is well ventilated
during this operation. It is normal for the appliance to emit small cracking sounds when you turn it on if
the first time.
Read all instructions before using this heater.
Caution very hot surface. Caution: Some parts of this product may become very hot and cause burns. Spec' al
2.
attention must be paid to this fact in the presence of children and handicapped persons. This appliance can be
used by children from the age of 8 and older, and persons with lower physical, sensory or mental abilities or a
lack of experience or knowledge providing they are under supervision or have been trained in the use of the
appliance in a safe manner and understand the possible danger. Children may not play with the appliance. This
device must be plugged or connected according to the rules and standards applicable by an authorized person.
The instruction book of this product is available by contacting the after-sales service with the number indicate
on the warranty part included in this manual service.
4. If the power cable is damaged, it must be replaced by the manufacturer, its after salesservice or similarly
qualified persons in order to avoid any danger.
Caution: To avoid overheating and for safety reasons, do not cover the panel heater.
6. Devices with this symbol should not be disposed with household waste but must be collected separately
and recycled. The collection and recycling of end of life must be made according to the provisions and local
ordinances (DEEE2002/96/CE).
he installation of the device in high altitude causes an increase of the temperature air outlet (about 10 C per
7.
1000 m elevation). In case of mobile utilization of the device (see applicable models below):
8. Do not use this heater near a bathtub, a shower or a pool. - Do not use this heater in small areas when they
are occupied by people unable to leave the room by themselves unless if a constant supervision is provided.
Control function
Checkthe householdvoltage to ensure it matchesthe appliance'sratedspecification.Besureto plug into a 220-240V,
50-60Hz outlet.
Control panel introduce.
On/off key
Mode setting key
2.
Timer key
4. Program setting key
5. Power setting key
Open-window function key
6.
Up key
7.
8. Down key
9. LED display
10. Power indicator light
Comfort indicator light
11.
Anti-frost indicator light
12.
13. Timer indicator light
14. Open-window function indicator light
Auto indicator light
15.
16. User indicator light
Weekly Pre-set pro-
gram
Monday-Friday
Saturday- Sunday
Monday-Friday P2
Saturday-Sunday
Monday-Sunday
Monday-Sunday
p4
Monday-Sunday
USING THIS HEATER
11 15
6b.
dinitol
Installation place
Bedroom, Hallways, Kitchen, Living room, Dining room,
Bathroom, Conservatory
Bedroom, Hallways, Kitchen, Living room, Dining room,
Bathroom, Conservatory
Office
Office
Commercial location
Home, end user power on the machine when need heat,
if not, then power off
14:00pm- 17:00pm Home, end user need to travel out,
while just power on the machine with 5C to prevent frost
1. Function introduction
Whenfirst power on the machine, it will havebeep sound,LEDdisplay24.0Cthedot will keepflash until end user set
the time. Factorydefault high level heat temperature is 24 Oc,itcould be setfrom 5 oc to 350Cby user.
Default working mode is P4.
1.Switch the power on by pressing I position. By pressing on the O position, the heater will power off.
Under standby mode, press On/Off key could let the machine start to work.
Press it for 3s, heater will stop working and enter into standby mode.
1.2 Power setting / mode setting: when the power button is pressed, the modes switch to AUTO-USER-5-4-3-2-1-
AUTO... AUTO - maintaining the set temperature at the optimum power level.
1.3Temperaturesetting, underworking mode, pressUp and Downkey to set the temperature, from 5-350C.
1.4 Comfort indicator light: when the heater is in comfort mode, it light on.
1.5 Anti-frost indicator light: when heater is working in anti-frost mode, it light on.
1.6 Open window indicator light: when window function is effective, it light on.
The function module is equipped with an accurate thermal cut out. It has a built in memory with 6 heating programs,
of which 5 are factory pre-set and 1are available for programming
2. Setting the day and time
When the panel heater is first installed, has been switched off or disconnected from the mains supply for more than
72 hours, the Day and Time will need to be set.
2.1 Under working mode, press Time button for 3 seconds, LED window will display dl, and flash, use "Up" or "Down"
button to choose the correct day. It's from dl to d7 means from Monday to Sunday. Press Time button to confirm
the date.
2.2 After confirm the date. LED window switches to hour setting. The display flash "O", use "Up" or "Down" button to
choose the correct hour. It's from O to 23. Press Time button
2.3 Onceconfirm the hour.LEDwindow switchesto minute setting. Thedisplayflash "O", u se"Up"or"Down"button to
choose the correct minute. It's from
2.4 After confirm the time setting, 10 seconds after, LED window display temperature.
2.5 During above setting, press"Up"or"Down"button for 2 seconds,time data will be adjusted continuously.
2.5 If want to check the time, just pressTime button, it will show the Day, Hour, Minutes continuous. 3 seconds later,
it quite check and recover to show temperature.
3. Setting temperature
LEDwindow display setting temperature, press"Up"or"Down" button to choosethe requiredtemperature for high
level working period, it'sfrom 5 oc to 350C.Forlow levelworking period,default temperature is 5 oc, can't be altered.
4. Modes setting:
Press mode key, there are 6 programs which switch the heating between Comfort mode and Anti-frost
various times of the day and night. PI-P5 is pre-set and cannot be altered.The 'UP" programscan be defined by
the user.
Boilo The table below shows the running times for each of the program.
Economic OFF ON
temp.
(OFF)
50c
oo:ooam- 6:30am-
6:30arn 8:30arn
50C
00:00am- 7:30am-
7:30am 10:00am
soc
00:00am- 6:00am-
6:00am 17:00pm
50C
oo:ooam.
24:oopm
50C
00:00am- 6:00am-
6:00am 22:00pm
soc
0:00am-
24:00pm
50C
0:00am-
24:00pm
User program, runs at the time defined by the use
IP24
by the user.
to confirm the hour.
00 to 59. Press Time button to confirm the minute.
OFF ON OFF
8:30am- 17:ooprn- 22:30prn-
17 :oopm 22:30pm 24:oopm
10:00am- 12:00pm- 14:00pm-
12:00am 14:00pm 17:00pm
17:00pm-
24:00pm
22:00pm-
24:00pm
mode at
ON OFF
17:00pm- 22:30pm-
22:30pm 24:00pm