Polti QUICK&COMFORT QC110 Bedienungsanleitung Seite 11

WARNING: When the temperature is set to
the levels •• / • / MIN, the steam (4) must
be set to the zero position (steam off/dry
ironing) otherwise water could leak out
with the steam.
5. STEAM JET
To make ironing faster and easier the STEAM
JET function can be activated, which is ideal
for removing the most stubborn wrinkles. To
activate it, press the button
Activate the Steam Jet every few seconds,
one after another.
If the iron temperature light comes on while
this function is being used, wait until it turns
back off (the iron returns to the desired
temperature).
WARNING: The STEAM JET function only
works when the temperature is set to the
••• or MAX level.
6. SPRAY FUNCTION
The Spray function is perfect for dampening
the entire surface of the fabric in a uniform
manner, making it easier to remove stubborn
wrinkles. To activate it, press the button
(7-8).
7. VERTICAL IRONING
The iron may be used in the vertical position
to remove creases from fabrics and/or to
refresh fabric fibres, eliminating any residual
odours. During vertical use, to activate the
release of steam press the steam boost button
(5-6).
8. AUTO SHUT-OFF FUNCTION
When the Polti Vaporella Quick&Comfort is
not used, the Auto Shut-Off safety function
activates. The time before activation varies
based on the position of the iron and starts
from the last completed action:
Vertical position: around 8 minutes
Resting or horizontal position: around 1
minute.
When the Auto Shut-Off function is activated,
the heating indicator light (9) will flash and
the iron will go into stand-by
To reactivate the device, simply move it.
Before ironing again, wait until the heating
light turns off.
9. OUT OF WATER
When the device no longer dispenses steam,
it means that there is no water in the tank.
To begin using steam again, simply remove
the power supply from the electric socket and
fill the tank as described in chapter 1.
10. SELF CLEAN SYSTEM
The Polti Vaporella Quick&Comfort Self Clean
system ensures removal of limescale, thus
guaranteeing a better supply of steam and
(5-6).
avoiding the leakage of dirt from holes in the
plate which can create stains.
Regularly run the Self Clean cycle to ensure
better performance and durability over time.
It is recommended that the cycle be run at
least once a month.
In any case, it is possible to perform the
cleaning cycle at any time.
Before running the cleaning cycle, make sure
you have a large receptacle or bowl on hand
to collect the water, steam and limescale that
will come out from the iron during the process,
thus avoiding the wetting of the ironing board
or surface on which you are ironing.
How to perform the Self Clean limescale
cleaning cycle:
10.1 Unplug the power supply cord from the
electric socket.
10.2 Set the steam adjustment to the zero
position (=steam OFF)
10.3 Fill the water tank as described in
Chapter 1.
10.4 Plug the power supply cord into the
electric socket.
10.5 Turn on the appliance, setting the
temperature to the MAX level.
10.6 Wait for the iron temperature light to
turn on/off twice.
10.7 Then unplug the power supply cord from
the electric socket again.
10.8 Hold the device horizontally around 15
cm from a receptacle/bowl and hold down
the Self Clean button to begin the cleaning
cycle (10-11). Shake the iron lightly to better
empty the tank.
10.9 When the tank is empty, release the Self
Clean button.
10.10 Plug the power supply cord into the
electric socket.
10.11 Turn on the appliance, setting the
. temperature to the MAX level.
10.12 When the iron is ready (the light stays
on), lightly shake it over a cloth, so as to
remove any water drops which may still be on
the plate.
| 11 |
(4).